Fix annoying build warning:
drivers/usb/serial/ftdi_sio.c:890: warning: enumeration value `FT232RL' not handled in switch
Also add logic to detect FT232R chips (version 6.00, usb 2.0 full speed),
so that case isn't completely useless. (NOTE: FT232RL and FT232RQ are
the same chip in different packages: L is SSOP, Q is QFN.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix annoying build warning when CONFIG_USB_SERIAL_GENERIC is undefined.
drivers/usb/serial/generic.c:24: warning: `generic_probe' declared `static' but never defined
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Both airprime and option now want to handle vendor ID 0x1410,
device ID 0x1100. Airprime calls it 'ExpressCard34 Qualcomm 3G CDMA'.
Option calls it 'Novatel Merlin XS620/S640'. Patch attached to remove it
from airprime.
From: Jon K Hellan <jon.kare.hellan@uninett.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves all of the Novatel device ids to the option driver, where
they belong.
Thanks to Novatel for providing a list of all supported devices.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add an ID to recognise the Novatel EV620 wireless adapter.
http://www.novatelwireless.com/products/expedite/ev620.html
It looks like a mini PCI-Express adapter. The mPCIE connector includes USB
pins... the card shows up to the system as a USB device, and powers itself
from the PCI bus.
The card I have isn't activated yet, so I can't get a PPP session up yet, but
I have tested basic serial communication successfully in both 2.6.18 and
2.6.20 kernels, once the product ID was added. (the driver changed quite a
bit between the two revs.) In both drivers, it responds to AT commands and
such.
Signed-off-by: Mark Glines <mark@glines.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
these devices have a shared interrupt endpoint. For serialcore to pass
an interrupt endpoint to a subdriver, the subdriver must define and
_export_ a fitting callback. The mos7720 driver failed to do so. This led
invariably to an oops upon open. This patch fixes it. The driver is useless
without it. Please try to get this into 2.6.21 and the stable kernels that
have this driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch reverts d9a7ecacac since it
breaks drivers that need to access the ->port[] array in shutdown
(most of them).
Signed-Off: Jim Radford <radford@blackbean.org>
Acked-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch adding the PID for the FT232RL to ftdi_sio. The patch
generates a warning during compilation because get_ftdi_divisor doesn't
explicitly handle the FT232RL with this patch, so I guess you don't want
to use it in its current state. It is all I could come up with with the
knowledge I have of the drivers at the moment, though, and I hope you
can have some use for it at least. It works fine with my DLP-TILT with
an FT232RL.
From: Gard Spreemann <spreeman@stud.ntnu.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Montag, 26. Februar 2007 15:16 schrieb Craig Schlenter:
> Hi Greg
>
> 34ef50e5b1 is definitely
> the source of the problem. Reverting that makes the
> ftdi port show up as ttyUSB0 again for me and it
> can actually be opened.
This patch should fix the issue.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Craig Schlenter <craig@codefountain.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I encountered some problems with the airprime driver in use with a Novatel
Merlin XU870:
Closing an open Connection to e.g. /dev/ttyUSB0 doesn't reset the
RTS/DTR lines of the Modem. Consequently, when I use minicom to
establish a connection by "ATD*99#" the modem doesn't hang up even if i
exit minicom and so I cannot reuse the modem unless I remove it and plug
it in again.
With the attached patch, the RTS/DTR lines are resetted on a close. The
code was mainly taken from the option.c driver.
Convert all the port specific code in attach / shutdown to use the new
port_probe / port_register callbacks from device_register /
device_unregister allowing adding the sysfs attributes to be added at
the correct time and to the serial port device itself, instead of to
the unadorned usb device, avoiding a NULL dereference.
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ensure that the ->port_remove() callbacks get called before the
->shutdown() callback which makeing the order symmetric with
->attach() being called before ->port_probe().
Signed-off-by: Jim Radford <radford@blackbean.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've developed some devices with FTDI chips (FT232xx). FTDI was so kind
to give some own PID's which I can use together with their VID. Some of
the devices are already very popular here and I have customers from
universities, institutes .....
I use the FTDI VID 0x0403. My PID's are:
0xff38 - IBS US485 (USB<-->RS422/485 interface)
0xff39 - IBS PIC-Programmer
0xff3a - IBS Card reader for PCMCIA SRAM-cards
0xff3b - IBS PK1 - Particel counter
0xff3c - IBS RS232 - Monitor
0xff3d - APP 70 (dust monitoring system)
0xff3e - IBS PEDO-Modem (RF modem 868.35 MHz)
0xff3f - future device
The company is "IBS Ing.-Buero Schleusener".
From: Thomas Schleusener <thomas@be-schl.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here are two new device IDs for the cp2101 driver.
The diff is with linus's tree as of this evending.
From: Jon K Hellan <hellan@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to add the VID and PID for Telldus Technologies Homeautomation
usb-dongle to the ftdi_sio driver.
From: Micke Prag <micke.prag@telldus.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds all of the known Option device ids to the driver.
Many thanks to some Option engineers for getting me this list.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no need to have two tables with the same device ids in it.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds another usb id to the cp2101. It seems to work well.
Please apply, thanks.
Signed-off-by: Pozsar Balazs <pozsy@uhulinux.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
from: Kevin Lloyd <linux@sierrawireless.com>
This patch removes the Airprime 5220 device (branded as Audiovox) from
the option.c driver. This device is already supported by the sierra.c
driver.
This was based off of the option.c driver found in kernel 2.6.20-git11.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix up the error processing path: in usb_submit_urb failed, we forgot
to free buffers. Also, don't free buffers in read callback: less error
prone, 21 LOC less, no need to comment so much. N.B. write path is ok
to do kfree.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I added two fields to struct usb_serial_port to keep track of the
throttle state. Other usb-serial drivers typically use private data for
such things, but the generic driver can not really do that because some
of its code is also used by other drivers (which may have their own
private data needs).
As it is, I am not sure that this patch is useful in all scenarios.
It is certainly helpful for low-bandwidth devices that can hold their
data in response to throttling. But for devices that pump data in
real-time as fast as possible (webcam, A/D converter, etc), throttling
may actually cause more data loss.
From: Joris van Rantwijk <jorispubl@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch ensures that the device is turned on when inserted into the system.
It also adds more VID/PIDs and matches the N_OUT_URB with the airprime driver.
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- fix an error code returned if a device has been disconnected
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- take BKL before looking up a driver to associate with a device to make
sure the module is not unloaded after looking up but before association
& bumping module count
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- introduce a spinlock for serial_table to eliminate the window between
looking up a device and getting a reference
- delay inscription of a new device into serial_table until it is fully
initialised
- make sure disconnect() kills all URBs to avoid leckage across a soft unbind
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At least the Keyspan USA-19HS USB-to-serial converter supports
two different configurations, one where the input endpoints
have interrupt transfer type and one where they are bulk endpoints.
The default UHCI configuration uses the interrupt input endpoints.
The keyspan driver, OTOH, assumes that the device has only bulk
endpoints (all URBs are initialized by calling usb_fill_bulk_urb
in keyspan.c/ keyspan_setup_urb). This causes the interval field
of the input URBs to have a value of zero instead of one, which
'accidentally' worked with Linux at least up to 2.6.17.11 but
stopped to with 2.6.18, which changed the UHCI support code handling
URBs for interrupt endpoints. The patch below modifies to driver to
initialize its input URBs either as interrupt or as bulk URBs,
depending on the transfertype contained in the associated endpoint
descriptor (only tested with the default configuration) enabling
the driver to again receive data from the serial converter.
Greg K-H reworked the patch.
Signed-off-by: Rainer Weikusat <rweikusat@sncag.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While adding the dynamic-id support to usb serial I found a small bug in
the air cable driver:
Adds module and name information to the usb_serial_driver instance
of aircable. So the aircable driver is correctly shown under
/sys/bus/usb-serial/drivers/aircable and has the module link.
Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Every usb serial driver should have a pointer to the corresponding usb driver.
So the usb serial core can add a new id not only to the usb serial driver, but
also to the usb driver.
Also the usb drivers of ark3116, mos7720 and mos7840 missed the flag
no_dynamic_id=1. This is added now.
Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thanks to Johannes Hölzl <johannes.hoelzl@gmx.de> for fixing a few
things and getting it all working properly.
This adds support for dynamic usb ids to the usb serial core. The file
"new_id" will show up under the usb serial driver, not the usb driver
associated with the usb-serial driver (yeah, it can be a bit confusing
at first glance...)
This patch also modifies the USB core to allow the usb-serial core to
reuse much of the dynamic id logic.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Johannes Hölzl <johannes.hoelzl@gmx.de>
This patch adds EPiC support to the io_edgeport driver which adds
support for a number of NCR printers:
- NCR (Axiohm) 7401-K580 printer
- NCR (TEC) 7401-K590 printer, 7402-K592
- NCR (TEC) 7167, 7168 printers
- NCR (TEC) 7197, 7198, F306, F307, F309 printers
- NCR (Axiohm) 7194 printer
- NCR (Axiohm) 7158 printer
and a few more.
It is based on the 2.6.19 kernel.
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Fix void cast and re-enable on sparc.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/usb/serial/funsoft.c: In function `funsoft_ioctl':
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_iflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_iflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_iflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_oflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_oflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_oflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_lflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_lflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_lflag' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_line' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_line' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_line' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
drivers/usb/serial/funsoft.c:35: warning: dereferencing `void *' pointer
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: error: request for member `c_cc' in something not a structure or union
drivers/usb/serial/funsoft.c:35: warning: type defaults to `int' in declaration of `type name'
Cc: David Clare <david@funsoft.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just the serial port in the first interface should control DTR and RTS
lines. This way, the closing of the rest of the ports does not produce a=
hangup in the communication.
Signed-off-by: Miguel Angel Alvarez <ma.alvarez@ziv.es>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add USB vendor/device IDs for Novatel Wireless S720 and U720 CDMA/EV-DO
modems to airprime.c.
Signed-off-by: Eric Smith <eric@brouhaha.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added VendorId and ProductId for Huawei E220 USB Modem
Signed-off-by: Johann Wilhelm <johann.wilhelm@student.tugraz.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added a device specific ioctl function to prevent the disabling of canonical
mode. EINVAL is returned for any TCSETSF ioctl that doesn't have ICANON set.
This patch is for 2.6.17 or later kernels.
When "hwinfo --modem" is executed it opens the funsoft USB serial device and
disables canonical mode. The device is kept this way until hwininfo has
finished probing any modems on a system. The funsoft device expects to be
running in canonical mode. Switching the device to raw mode can cause
incomplete data packets and device timeouts.
Signed-off-by: David Clare <david@funsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch adds the Baltech Reader ID to the list of USB IDs in the
CP2101 driver.
From: Johannes Hoelzl <johannes.hoelzl@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several drivers have bogus ioctl code that tries unneccessarily to
override the standard processing. In the three cases here the actual code
is not only wrong but also not required as they implement the proper
set_termios method as well.
Remove the junk.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
below is a patch for the ftdi_sio driver to include a new device ID for
CCS MachX PIC programmer.
From: Jan Capek <jan@ccsinfo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Brownell