The PRCM (Power/Reset/Clock Management) unit provides several clock
devices:
- AR100 clk: used to clock the Power Management co-processor
- AHB0 clk: used to clock the AHB0 bus
- APB0 clk and gates: used to clk peripherals connected to the APB0 bus
Add support for these clks in a separate driver so that they can be probed
as platform devices instead of registered during early init.
This is needed to be able to probe PRCM MFD subdevices.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Prevent the SDRAM controller from being gated by force-enabling it in the
machine code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Right now, AHB is an indirect child clock of the CPU clock. If that
happens to change, since the CPU clock has no other consumers declared
in Linux, it would be shut down, which is not really a good idea.
Prevent this by forcing it enabled.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Since we start to have a lot of clocks to protect, some of them in a
few SoCs only, it becomes difficult to handle the clock protection
without having to add per machine exceptions.
Add per-SoC data to tell which clock to leave enabled.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Since we have a folder of our own, we can actually make use of it by
splitting the huge clock file into several sub drivers.
The gmac clock is pretty easy to deal with, since it's pretty much
isolated and doesn't have any dependency on the other clocks.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Since we have a folder of our own, we can actually make use of it by
splitting the huge clock file into several sub drivers.
The main oscillator is pretty easy to deal with, since it's pretty much
isolated.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Callers of clk_put must disable the clock first. This also means that
as long as the clock is enabled the driver should hold a reference to
that clock. Hence, the call to clk_put here are bogus and should be
removed.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
The A31 USB clock slightly differ from its older counterparts, mostly
because it has a different gate for each PHY, while the older one had
a single gate for all the phy.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
MPU DPLL on OMAP5, DRA75x, DRA72x has a limitation on the maximum
frequency it can be locked at. Duty Cycle Correction circuit is used
to recover a correct duty cycle for achieving higher frequencies
(hardware internally switches output to M3 output(CLKOUTHIF) from M2
output (CLKOUT)).
So provide support to setup required data to handle Duty cycle by
the setting up the minimum frequency for DPLL. 1.4GHz is common
for all these devices and is based on Technical Reference Manual
information for OMAP5432((SWPU282U) chapter 3.6.3.3.1 "DPLLs Output
Clocks Parameters", and equivalent information from DRA75x, DRA72x
documentation(SPRUHP2E, SPRUHI2P).
Signed-off-by: Nishanth Menon <nm@ti.com>
[t-kristo@ti.com: updated for latest dpll init API call]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
In order to get correct clock dividers for AESS/ABE we need to set the
dpll_abe_m2x2_ck rate to be double of dpll_abe_ck.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Commit 99cbd064b0 ("clk: qcom: Support display RCG clocks") adds
a use of the __clk_round_rate in a clock provided that can be built
as a loadable module.
This exports the symbol to avoid the build error from compiling
the qcom clock as a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
commit a183da63 introduced a new error return path that does
not kfree icst if the kmemdup of desc->params fails.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The EXYNOS5410 clocks are statically listed and registered
using the Samsung specific common clock helper functions.
Signed-off-by: Tarek Dakhran <t.dakhran@samsung.com>
Signed-off-by: Vyacheslav Tyrtov <v.tyrtov@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Not all clocks are implemented but client drivers can still
request them. Currently we will return a NULL pointer to them if
the clock isn't implemented in software but NULL pointers are
valid clock pointers. Return an error pointer so that driver's
don't proceed without a clock they may actually need.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
A new PLL (gpll4) is added on msm8974 PRO devices to support a
faster sdc1 clock rate. Add support for this and the two new sdcc
cal clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The display clocks all source from dedicated phy PLLs within their
respective multimedia hardware block. Hook up these PLLs to the
display clocks with the appropriate parent mappings, clock flags,
and the appropriate clock ops. This should allow the display
clocks to work once the appropriate phy PLL driver registers their
PLL clocks.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for the DSI/EDP/HDMI RCG clocks. With the proper
display driver in place this should allow us to support display
clocks on msm8974 based devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some drivers may want to call clk_set_rate() with a very large
number to force the clock to go as fast as it possibly can
without having to know the range between the highest rate and
second highest rate. Add support for this by defaulting to the
highest rate in the frequency table if we can't find a frequency
greater than what is requested.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
We forgot to add the status bit for the PLLs and we were using
the wrong register and masks for configuration, leading to
unexpected PLL configurations. Fix this.
Fixes: d8b212014e (clk: qcom: Add support for MSM8974's multimedia clock controller (MMCC))
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
If the bit is set the clock is off so we should be checking for
a clear bit, not a set bit. Invert the logic.
Fixes: bcd61c0f53 (clk: qcom: Add support for root clock generators (RCGs))
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This driver deals with the core clocks found on Marvell Berlin BG2Q. For the
shared register dividers, make use of the corresponding driver and add some
single clock muxes and gates for the rest.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This driver deals with the core clocks found on Marvell Berlin
BG2 and BG2CD. For the shared register dividers, make use of the
corresponding driver and add some single clock muxes and gates for
the rest.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a driver for the complex divider cells found on Marvell Berlin2
SoCs. The cells come in two flavors: single register cells and shared
register cells.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a clock driver for the simple PLLs found on Berlin SoCs.
With repect to PLL registers and features, BG2/BG2CD and BG2Q are
slightly different, e.g. different allowed VCO dividers and bit
shifts.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This is a driver for the AVPLLs built upon a VCO with 8 channels each
found on Marvell Berlin2 SoCs. While both VCOs found on BG2/BG2CD share
the same register set, sometimes registers shifts for one of the VCOs
are a bit off. Nothing serious that should require a separate driver,
so deal with both VCOs in a single driver instead.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Failure to terminate this match table can lead to boot failures
depending on where the compiler places the match table.
Cc: Gabriel FERNANDEZ <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Audio Tracking Logic is designed to be used by HD Radio applications to
synchronize the audio output clocks to the baseband clock. ATL can be also
used to track errors between two reference clocks (BWS, AWS) and generate a modulated
clock output which averages to some desired frequency.
In essence ATL is generating a clock to be used by an audio codec and also
to be used by the SoC as MCLK.
To be able to integrate the ATL provided clocks to the clock tree we need
two types of DT binding:
- DT clock nodes to represent the ATL clocks towards the CCF
- binding for the ATL IP itself which is going to handle the hw
configuration
The reason for this type of setup is that ATL itself is a separate device
in the SoC, it has it's own address space and clock domain. Other IPs can
use the ATL generated clock as their functional clock (McASPs for example)
and external components like audio codecs can also use the very same clock
as their MCLK.
The ATL IP in DRA7 contains 4 ATL instences.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
To allign the name with the other atl clock names:
atlclkin3_ck -> atl_clkin3_ck
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Composite interface clock is needed by OMAP2, but it was only built
in for OMAP3. Fixed the conditional build flag checks for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Adds support for registering the alias clocks, boot time clock-enable list
and disabling autoidle of clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2430 I2CHS modules require specific hardware ops to be used, so added
a new compatible string for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2 has slightly different DPLL compared to later OMAP generations.
This patch adds support for the ti,omap2-dpll-core-clock and also adds
the bindings documentation.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AMxxxx dpll_data previously had autoidle_mask set, even if these SoC:s
don't have autoidle register. Remove the bit-field value as it is unused,
also drop the unnecessary DPLL_HAS_AUTOIDLE flag passing during init,
as we can just simply check against the contents of the autoidle_mask.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Fixes the following warning:
WARNING: drivers/built-in.o(.text.unlikely+0x2c50): Section mismatch in reference from the function exynos4_clk_sleep_init() to the (unknown reference) .init.data:(unknown)
The function exynos4_clk_sleep_init() references
the (unknown reference) __initdata (unknown).
This is often because exynos4_clk_sleep_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Commit c686078 ("clk: divider: Add round to closest divider") introduced
a helper function to check whether given divisor is the best one instead
of direct check. However due to int type used instead of unsigned long
for passing calculated rates to this function in certain cases an
overflow could occur, for example when trying to obtain maximum possible
clock rate by calling clk_round_rate(..., UINT_MAX).
This patch fixes this issue by changing the type of rate, now and best
arguments of the function to unsigned long, which is the type that
should be used for clock rates.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Failure to terminate this match table can lead to boot failures
depending on where the compiler places the match table.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Implement the clk->determine_rate method for Broadcom Kona peripheral
clocks. This allows a peripheral clock to be re-parented in order to
satisfy a rate change request. This takes the place of the previous
kona_peri_clk_round_rate() functionality, though that function remains
because it is used by the new one.
The parent clock that allows the peripheral clock to produce a rate
closest to the one requested is the one selected, though the current
parent is used by default.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
"clk: samsung: clk-s3c2410-dlck: do not use PNAME macro as it declares
__initdata" had a typo in it which caused build failure. Trivial fix.
Signed-off-by: Olof Johansson <olof@lixom.net>
The originally used PNAME macro from the core samsung clock infrastructure
declares the created array as initdata, creating section mismatch warnings
in the dclk driver.
Thus declare them directly, removing these warning.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the missing sysmmu clocks for Display and
ISP blocks.
Signed-off-by: Cho KyongHo <pullip.cho@samsung.com>
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now with common clock support added for exynos5250 it is necessary to
move this code to exynos5250 common clock driver as clock registers
should be handled there. This change is tested in exynos5250 based
arndale platform.
Cc: Abhilash Kesavan <a.kesavan@samsung.com>
Cc: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsugn.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
[t.figa: Rebased onto current kernel sources.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The address of the blsp2_ahb_clk register is incorrect. Fix it.
Signed-off-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch adds support for S2MPS14 PMIC clocks (BT and AP) to the
s2mps11 clock driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
There is no need for checking if 'clk_table' is not NULL twice (first
after allocation and second at the end of probe()). Also move allocation
of this 'clk_table' to probe from s2mps11_clk_parse_dt as this is
logical place for it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add of_clk_del_provider to remove previously registered clock provider.
Add of_node_put to decrement the ref count of clock nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
When it fails to allocate div, gate should be free'd before return
Signed-off-by: Valentin Ilie <valentin.ilie@gmail.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Commit 1d9fe6b97 ("clk: divider: Fix best div calculation for power-of-two and
table dividers") introduces a regression in its _table_round_up function.
When the divider passed to this function is greater than the max divider
available in the table, this function returns table's max divider.
Problem is that it causes an infinite loop in clk_divider_bestdiv() because
_next_div() will never return a value greater than maxdiv.
Instead of returning table's max divider, this patch returns INT_MAX.
Reported-by: Fabio Estevam <festevam@gmail.com>
Reported-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Boris BREZILLON