Separate out pci_add_dynid() from store_new_id() and export it so that
in-kernel code can add PCI IDs dynamically. As the function will be
available regardless of HOTPLUG, put it and pull pci_free_dynids()
outside of CONFIG_HOTPLUG.
This will be used by pci-stub to initialize initial IDs via module
param.
While at it, remove bogus get_driver() failure check.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is the first of three patches that implement a bit field that PCI
Express device drivers can use to indicate they need a fundamental reset
during error recovery.
By default, the EEH framework on powerpc does what's known as a "hot
reset" during recovery of a PCI Express device. We've found a case
where the device needs a "fundamental reset" to recover properly. The
current PCI error recovery and EEH frameworks do not support this
distinction.
The attached patch (courtesy of Richard Lary) adds a bit field to
pci_dev that indicates whether the device requires a fundamental reset
during recovery.
These patches supersede the previously submitted patch that implemented
a fundamental reset bit field.
Signed-off-by: Mike Mason <mmlnx@us.ibm.com>
Signed-off-by: Richard Lary <rlary@us.ibm.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Background:
Graphic devices are accessed through ranges in I/O or memory space. While most
modern devices allow relocation of such ranges, some "Legacy" VGA devices
implemented on PCI will typically have the same "hard-decoded" addresses as
they did on ISA. For more details see "PCI Bus Binding to IEEE Std 1275-1994
Standard for Boot (Initialization Configuration) Firmware Revision 2.1"
Section 7, Legacy Devices.
The Resource Access Control (RAC) module inside the X server currently does
the task of arbitration when more than one legacy device co-exists on the same
machine. But the problem happens when these devices are trying to be accessed
by different userspace clients (e.g. two server in parallel). Their address
assignments conflict. Therefore an arbitration scheme _outside_ of the X
server is needed to control the sharing of these resources. This document
introduces the operation of the VGA arbiter implemented for Linux kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some devices allow an individual function to be reset without affecting
other functions in the same device: that's what pci_reset_function does.
For devices that have this support, expose reset attribite in sysfs.
This is useful e.g. for virtualization, where a qemu userspace
process wants to reset the device when the guest is reset,
to emulate machine reboot as closely as possible.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since this function should never modify it (saves warnings when called with
const args too).
Signed-off-by: Alexey Zaytsev <zaytsev@altell.ru>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Other functions use type bool, so use that for pci_enable_wake as well.
Signed-off-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch enhances the FLR functions:
1) remove disable_irq() so the shared IRQ won't be disabled.
2) replace the 1s wait with 100, 200 and 400ms wait intervals
for the Pending Transaction.
3) replace mdelay() with msleep().
4) add might_sleep().
5) lock the device to prevent PM suspend from accessing the CSRs
during the reset.
6) coding style fixes.
Reviewed-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Based on PCI Express AER specs, a root port might receive multiple
TLP errors while it could only save a correctable error source id
and an uncorrectable error source id at the same time. In addition,
some root port hardware might be unable to provide a correct source
id, i.e., the source id, or the bus id part of the source id provided
by root port might be equal to 0.
The patchset implements the support in kernel by searching the device
tree under the root port.
Patch 1 changes parameter cb of function pci_walk_bus to return a value.
When cb return non-zero, pci_walk_bus stops more searching on the
device tree.
Reviewed-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Zhang Yanmin <yanmin_zhang@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Create symbolic link to hotplug driver module in the PCI slot
directory (/sys/bus/pci/slots/<SLOT#>). In the past, we need to load
hotplug drivers one by one to identify the hotplug driver that handles
the slot, and it was very inconvenient especially for trouble shooting.
With this change, we can easily identify the hotplug driver.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Reviewed-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_bus_set_ops changes pci_ops associated with a pci_bus. This can be
used by debug tools such as PCIE AER error injection to fake some PCI
configuration registers.
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch (as1235) adds an array of PCI power-state names, together
with a simple inline accessor routine.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for PCI Express transaction layer end-to-end CRC checking
(ECRC). This patch will enable/disable ECRC checking by setting/clearing
the ECRC Check Enable and/or ECRC Generation Enable bits for devices that
support ECRC.
The ECRC setting is controlled by the "pci=ecrc=<policy>" command-line
option. If this option is not set or is set to 'bios", the enable and
generation bits are left in whatever state that firmware/BIOS set them to.
The "off" setting turns them off, and the "on" option turns them on (if the
device supports it).
Turning ECRC on or off can be a data integrity versus performance
tradeoff. In theory, turning it on will catch more data errors, turning
it off means possibly better performance since CRC does not need to be
calculated by the PCIe hardware and packet sizes are reduced.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The last in-tree caller of pci_find_slot has been converted, so
let's get rid of this deprecated interface.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We should not assign 64bit ranges to PCI devices that only take 32bit
prefetchable addresses.
Try to set IORESOURCE_MEM_64 in 64bit resource of pci_device/pci_bridge
and make the bus resource only have that bit set when all devices under
it support 64bit prefetchable memory. Use that flag to allocate
resources from that range.
Reported-by: Yannick <yannick.roehlly@free.fr>
Reviewed-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCIe ATS capability makes the Endpoint be able to request the
DMA address translation from the IOMMU and cache the translation
in the device side, thus alleviate IOMMU pressure and improve the
hardware performance in the I/O virtualization environment.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch sets up disabled bridges even if buses have already been
added.
pci_assign_unassigned_resources is called after buses are added.
pci_assign_unassigned_resources calls pci_bus_assign_resources.
pci_bus_assign_resources calls pci_setup_bridge to configure BARs of
bridges.
Currently pci_setup_bridge returns immediately if the bus have already
been added. So pci_assign_unassigned_resources can't configure BARs of
bridges that were added in a disabled state; this patch fixes the issue.
On logical hot-add, we need to prevent the kernel from re-initializing
bridges that have already been initialized. To achieve this,
pci_setup_bridge returns immediately if the bridge have already been
enabled.
We don't need to check whether the specified bus is a root bus or not.
pci_setup_bridge is not called on a root bus, because a root bus does
not have a bridge.
The patch adds a new helper function, pci_is_enabled. I made the
function name similar to pci_is_managed. The codes which use
enable_cnt directly are changed to use pci_is_enabled.
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The radeonfb driver needs to program the device's PMCSR directly due
to some quirky hardware it has to handle (see
http://bugzilla.kernel.org/show_bug.cgi?id=12846 for details) and
after doing that it needs to call the platform (usually ACPI) to
finish the power transition of the device. Currently it uses
pci_set_power_state() for this purpose, however making a specific
assumption about the internal behavior of this function, which has
changed recently so that this assumption is no longer satisfied.
For this reason, introduce __pci_complete_power_transition() that may
be called by the radeonfb driver to complete the power transition of
the device. For symmetry, introduce __pci_start_power_transition().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This API is used by the PCI core to rescan a bus and rediscover
newly added devices.
Over time, it is expected that the various PCI hotplug drivers
will migrate to this interface and away from the old
pci_do_scan_bus() interface.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce pci_is_root_bus helper function. This will help make code
more consistent, as well as prevent incorrect assumptions (such as
pci_bus->self == NULL on a root bus, which is not always true).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add or remove a Virtual Function after receiving a Migrate In or Out
Request.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add or remove the Virtual Function when the SR-IOV is enabled or
disabled by the device driver. This can happen anytime rather than
only at the device probe stage.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If a device has the SR-IOV capability, initialize it (set the ARI
Capable Hierarchy in the lowest numbered PF if necessary; calculate
the System Page Size for the VF MMIO, probe the VF Offset, Stride
and BARs). A lock for the VF bus allocation is also initialized if
a PF is the lowest numbered PF.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Add the new API pci_enable_msi_block() to allow drivers to
request multiple MSI and reimplement pci_enable_msi in terms of
pci_enable_msi_block. Ensure that the architecture back ends don't
have to know about multiple MSI.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
drivers/pci/hotplug/fakephp.c: In function 'pci_rescan_bus':
drivers/pci/hotplug/fakephp.c:271: warning: passing argument 1 of 'pci_bus_assign_resources' discards qualifiers from pointer target type
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce new function pci_msix_table_size() returning the size of
the MSI-X table of given PCI device or 0 if the device doesn't
support MSI-X.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes the ROM reading code return an error to user space if
the size of the ROM read is equal to 0.
The patch also emits a warnings if the contents of the ROM are invalid,
and documents the effects of the "enable" file on ROM reading.
Signed-off-by: Timothy S. Nelson <wayland@wayland.id.au>
Acked-by: Alex Villacis-Lasso <a_villacis@palosanto.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a problem in our handling of suspend-resume of PCI devices that
many of them have their standard config registers restored with
interrupts enabled and they are put into the full power state with
interrupts enabled as well. This may lead to the following scenario:
* an interrupt vector is shared between two or more devices
* one device is resumed earlier and generates an interrupt
* the interrupt handler of another device tries to handle it and
attempts to access the device the config space of which hasn't been
restored yet and/or which still is in a low power state
* the system crashes as a result
To prevent this from happening we should restore the standard
configuration registers of all devices with interrupts disabled and we
should put them into the D0 power state right after that.
Unfortunately, this cannot be done using the existing
pci_set_power_state(), because it can sleep. Also, to do it we have to
make sure that the config spaces of all devices were actually saved
during suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pcibios_enable_device() and pcibios_disable_device() don't handle
IRQs for devices that have MSI enabled and it should treat the
devices with MSI-X enabled in the same way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
During an online device reset it may be useful to disable bus-mastering.
pci_disable_device() does that, and far more besides, so is not suitable
for an online reset.
Add pci_clear_master() which does just this.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The VPD on all devices may not be 32K. Unfortunately, there is no
generic way to find the size, so this adds a simple API hook
to reset it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change PCI VPD API which was only used by sysfs to something usable
in drivers.
* move iteration over multiple words to the low level
* use conventional types for arguments
* add exportable wrapper
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds pci_common_swizzle(), which swizzles INTx values all the
way up to a root bridge.
This common implementation can replace several architecture-specific
ones. This should someday be combined with pci_get_interrupt_pin(),
but I left it separate for now to make reviewing easier.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch moves all definitions of the PCI resource names to an 'enum',
and also replaces some hard-coded resource variables with symbol
names. This change eases introduction of device specific resources.
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This cleanup removes unnecessary argument 'struct resource *res' in
pci_update_resource(), so it takes same arguments as other companion
functions (pci_assign_resource(), etc.).
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It's too large to be inlined.
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds pci_swizzle_interrupt_pin(), which implements the
INTx swizzling algorithm specified in Table 9-1 of the "PCI-to-PCI
Bridge Architecture Specification," revision 1.2.
There are many architecture-specific implementations of this
swizzle that can be replaced by this common one.
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Device drivers that use pci_request_regions() (and similar APIs) have a
reasonable expectation that they are the only ones accessing their device.
As part of the e1000e hunt, we were afraid that some userland (X or some
bootsplash stuff) was mapping the MMIO region that the driver thought it
had exclusively via /dev/mem or via various sysfs resource mappings.
This patch adds the option for device drivers to cause their reserved
regions to the "banned from /dev/mem use" list, so now both kernel memory
and device-exclusive MMIO regions are banned.
NOTE: This is only active when CONFIG_STRICT_DEVMEM is set.
In addition to the config option, a kernel parameter iomem=relaxed is
provided for the cases where developers want to diagnose, in the field,
drivers issues from userspace.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capability OSC_MSI_SUPPORT is set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the PCI
MSI driver. Also adds the function pci_msi_enabled, which returns true
if pci=nomsi is not on the kernel command-line.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capabilities OSC_ACTIVE_STATE_PWR_SUPPORT and
OSC_CLOCK_PWR_CAPABILITY_SUPPORT are set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the ASPM
driver. Also add the function pcie_aspm_enabled, which returns true if
pcie_aspm=off is not on the kernel command-line.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capability OSC_EXT_PCI_CONFIG_SUPPORT is set when the root
bridge is added with pci_acpi_osc_support() if we can access PCI
extended config space.
This adds the function pci_ext_cfg_avail which returns true if we can
access PCI extended config space (offset greater than 0xff). It
currently only returns false if arch=x86 and raw_pci_ext_ops is not set
(which might happen if pci=nommcfg is set on the kernel command-line).
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PM: Simplify the new suspend/hibernation framework for devices
Following the discussion at the Kernel Summit, simplify the new
device PM framework by merging 'struct pm_ops' and
'struct pm_ext_ops' and removing pointers to 'struct pm_ext_ops'
from 'struct platform_driver' and 'struct pci_driver'.
After this change, the suspend/hibernation callbacks will only
reside in 'struct device_driver' as well as at the bus type/
device class/device type level. Accordingly, PCI and platform
device drivers are now expected to put their suspend/hibernation
callbacks into the 'struct device_driver' embedded in
'struct pci_driver' or 'struct platform_driver', respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Was missing from the initial patch.
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We're getting a lot of storage drivers blamed for interrupt misrouting
issues. This patch provides a standard way of reporting the problem
... and, if possible, correcting it.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move the include of io.h down into the #ifdef __KERNEL__ protected
region.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In preparation for cleaning up the various hotplug drivers
such that they don't have to manage their own 'name' parameters
anymore, we provide the following convenience functions:
pci_slot_name()
hotplug_slot_name()
These helpers will be used by individual hotplug drivers.
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Slot detection drivers can co-exist with hotplug drivers. The names
of the detected/claimed slots may be different depending on module
load order.
For legacy reasons, we need to allow hotplug drivers to override
the slot name if a detection driver is loaded first (and they find
the same slots).
Creating and overriding slot names should be an atomic operation,
otherwise you get a locking nightmare as various drivers race to
call pci_create_slot().
pci_create_slot() is already serialized by grabbing the pci_bus_sem.
We update the API and add a 'hotplug' param, which is:
set if the caller is a hotplug driver
NULL if the caller is a detection driver
pci_create_slot() does not actually use the 'hotplug' parameter in this
patch. A later patch will add the logic that uses it.
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The GPL exported symbol pci_update_slot_number has been renamed to
pci_renumber_slot. Some of the safety checks were unnecessary and
were removed.
Cc: kristen.c.accardi@intel.com
Cc: matthew@wil.cx
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ingo pointed out that the m32r build was broken by pci_ioremap. It looks like
some files include pci.h w/o including io.h. The latter defines ioremap_* if
present, so it makes sense to include it in pci.h now that we have pci_ioremap
there.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Sometimes, it's necessary to enable software's ability to quiesce and
reset endpoint hardware with function-level granularity, so provide
support for it.
The patch implement Function Level Reset(FLR) feature following PCI-e
spec. And this is the first step. We would add more generic method, like
D0/D3, to allow more devices support this function.
The patch contains two functions. pcie_reset_function() is the new
driver API, and, contains some action to quiesce a device. The other
function is a helper: pcie_execute_reset_function() just executes the
reset for a particular device function.
Current the usage model is in KVM. Function reset is necessary for
assigning device to a guest, or moving it between partitions.
For Function Level Reset(FLR), please refer to PCI Express spec chapter
6.6.2.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tejun Heo