When we get a stream suspend event force the power down since otherwise
the stream would remain marked as active. In future we'll probably want
to make this stream-specific and add an interface to make the power down
of other widgets optional in order to support leaving bypass paths
active while suspending the processor.
Cc: stable@kernel.org
Reported-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Access to damp_power_widgets() is assumed to be single-threaded.
Concurrent accesses to dapm_power_widgets() may result in
unpredictable behavior.
Calls from:
close_delayed_work()
soc_codec_close()
soc_pcm_prepare()
soc_suspend()
soc_resume_deferred()
to snd_soc_dapm_stream_event() do not have the codec->mutex
taken to cover the call to dapm_power_widgets(). Thus, take
the mutex in these paths also to assure single-threaded use
of dapm_power_widgets().
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the SND_SOC_DAPM_LINE can be input or output, additional check is
needed in order to determine if the widget is connected as input or
output.
When checking for connected outputs, if the widget is line, than check
if the sources list is not empty (line is connected as output)
For input endpoint check, when the widget is line, also check if the
sinks list is not empty (line is connected as input).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently when built with DEBUG DAPM will dump information about
the power state decisions it is taking for each widget to dmesg.
This isn't an ideal way of getting the information - it requires
a kernel build to turn it on and off and for large hub CODECs the
volume of information is so large as to be illegible. When the
output goes to the console it can also cause a noticable impact
on performance simply to print it out.
Improve the situation by adding a dapm directory to our debugfs
tree containing a file per widget with the same information in
it. This still requires a decision to build with debugfs support
but is easier to navigate and much less intrusive.
In addition to the previously displayed information active streams
are also shown in these files.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the CODEC does not provide a set_bias_level() then update the
bias_level variable for it since other parts of the system expect
that to be maintained.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently DAPM interfaces with the audio streams to and from the
processor at the DAC and ADC widgets. As the digital capabilities
of parts increases this is becoming a less and less able to meet
the needs of parts.
To meet the needs of these devices create new widgets interfacing
with the TDM bus but not integrated into any other functionality.
Audio can then be routed to and from these widgets using existing
routing widgets.
A slot number is provided in the definition but this is currently
not used yet. This is intended to support devices which can use
more than one TDM slot on a single interface.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Speaker and headphone outputs do not need to be handled separately
since they can't be part of the same path.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the system doesn't have any DAPM widgets then we can't use their
state to check if the bias level for the codec should be up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In SOC DAPM layer of SOUND subsystem, when add signal route (in the
function snd_soc_dapm_add_route() ), the original code has wrong logic
when dapm layer check each widget whether an external one.
Signed-off-by: Rongrong Cao <rrcao@ambarella.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide an interval after the end of DAPM sequencing so that we
can distinguish between a pop in the final step of the sequence
and a pop generated from some other source outside DAPM.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that the audio subsystem is powered down cleanly when the system
shuts down by providing a shutdown operation. This ensures that all the
components have been returned to an off state cleanly which should avoid
audio issues from partially charged capacitors or noise on digital inputs
if the system is restarted quickly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Ben Dooks <ben-linux@fluff.org>
They are now only accessed within dapm_power_widgets() so can be local
to that function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Handle gain ramping for PGAs so we can coalesce their power updates too.
This is not ideal since we can't cope properly with gain ramping for
stereo paths but that was the case without coalescing and gain ramping
is relatively infrequently used so the effects are limited.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The more flexible value muxes and named mixers don't need to be sorted
differently from a power management point of view, they are different
only in terms of the control interface and not in terms of seqencing
behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reduce the number of register writes we need to set the power state for
a CODEC by coalescing updates to widgets with the same sequence order and
same register into a single write.
This can be a noticable performance improvement with slow or heavily
contended control buses, such as I2C controllers with a low clock
frequency, and is particularly noticable when resuming. It can also
reduce the noticability of and pops and clicks by ensuring that left
and right channels are powered simultaneously if they are in the same
register.
Currently widgets that have events are not coalesced, including PGAs
which may use the volume ramping control.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the remaining unsigned shorts with unsigned ints.
Tested with pcap2 codec (25 bits registers).
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lump the list walk into a single function, and pull in the power
application too so we can do some further refactoring. Pure code
motion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In the past the DAPM power sequencing was done by iterating over the list
of widgets once for each widget type and powering widgets of that type.
Instead of doing that do the sorting at the time we insert the widgets
into the lists of widgets to apply power changes to. This reduces the
amount of computation required for seqencing still further, though the
costs are generally dwarfed by the costs of the register writes
implementing them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than managing the bias level of the system based on if there is
an active audio stream manage it based on there being an active DAPM
widget. This simplifies the code a little, moving the power handling
into one place, and improves audio performance for bypass paths when no
playbacks or captures are active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM has always applied any changes to the power state of widgets as soon
as it has determined that they are required. Instead of doing this store
all the changes that are required on lists of widgets to power up and
down, then iterate over those lists and apply the changes. This changes
the sequence in which changes are implemented, doing all power downs
before power ups and always using the up/down sequences (previously they
were only used when changes were due to DAC/ADC power events). The error
handling is also changed so that we continue attempting to power widgets
if some changes fail.
The main benefit of this is to allow future changes to do optimisations
over the whole power sequence and to reduce the number of walks of the
widget graph required to check the power status of widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Many modern CODECs have shared resources on chip which must be enabled
for portions of the chip to work but which can be disabled at other times
in order to achieve power savings. Examples of such resources include
power supplies and some internal clocks.
Since these widgets are dependencies for the audio path but do not carry
audio signals they require slightly different handling to most widgets -
they do not contribute to the audio path and so should not be counted as
either inputs or outputs during path walks.
Cases where one supply provides a supply for another will require
additional work. There is also room for more optimisation of the graph
walking to avoid repeated checks for the same thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having switch statements at point of use make the DAPM
power check a member of the widget structure and set it when we
instantiate the widget.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This also switches us to using a switch statement for the widget type
in dapm_power_widget().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will form a basis for further power check refactoring: the overall
goal of these changes is to allow us to check power separately to
applying it, allowing improvements in the power sequencing algorithms.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is simple code motion, intended to support future refactoring of
the DAPM algorithms and (more immediately) the additon of events for
DACs and ADCs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_dapm_switch ends up ends up in dapm_new_mixer() (since a switch
is a special case of a mixer with only one input) but this wasn't
correctly handled in the code.
Also fix the coding style for the switch below while we're here.
Reported-by: Joonyoung Shim <dofmind@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On some systems it is desirable for control for DAPM pins to be provided
to user space. This is the case with things like GSM modems which are
controlled primarily from user space, for example. Provide a helper which
exposes the state of a DAPM pin to user space for use in cases like this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modify the check for the mux type to also handle the
snd_soc_dapm_value_mux type in a same way as the snd_soc_dapm_mux.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge the recently introduced soc_value_enum structure to the soc_enum.
The value based enums are still handled separately from the normal enum types,
but with the merge some of the newly introduced functions can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch allows you to define the mixer paths as having the same name as the
paths they represent.
This is required to support codecs such as the wm9705 neatly without extra
controls in the alsa mixer.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
This patch introduces a new enum type.
In this enum type each enumerated items referred with a value.
This new enum type can handle enums encoded in bitfield, or any other
weird ways. twl4030 codec has several mux selection register, where the
input/output mux is coded in a bitfield. With the normal enum type this type
of mux can not be handled in a clean way.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This should never happen and it's helpful to identify the specific control
that failed when it does happen.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
One of the issues with the ASoC v1 API which has been addressed in the
ASoC v2 work that Liam Girdwood has done is that the ALSA card provided
by ASoC is distributed around the ASoC structures. For example, machine
wide data such as the struct snd_card are maintained as part of the
CODEC data structure, preventing the use of multiple codecs. This has
been addressed by refactoring the data structures so that all the data
for the ALSA card is contained in a single structure snd_soc_card which
replaces the existing snd_soc_machine and snd_soc_device.
Begin the process of backporting this by renaming struct snd_soc_machine
to struct snd_soc_card, better reflecting its function and bringing it
closer to standard ALSA terminology.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Call device_create_file only once in snd_soc_dapm_sys_add function.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sound/soc/soc-dapm.c: In function 'snd_soc_dapm_sys_add':
sound/soc/soc-dapm.c:828: error: 'ret' undeclared (first use in this function)
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As well as ensuring that UI-relevant parts of control names don't get
truncated in the DAPM code this avoids conflicts in long control names
that differ only at the end of a long string.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
i.e. echo 6 59 >/sys/kernel/debug/soc-audio.0/codec_reg
will set register 0x06 to a value of 0x59.
Also, pop_time debugfs interface setup is moved so that it
is setup in the same function as codec_reg
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Mark Brown