This is a preparation for the dynamic power save support. In future there are
two paths to stop the master queues and we need to track this properly to
avoid starting queues incorrectly. Implement this by adding a status
array for each queue.
The original idea and design is from Johannes Berg, I just did
the implementation based on his notes. All the bugs are mine, of course.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also disable power save when disassociated. It makes no sense to have
power save enabled while disassociated.
iwlwifi seems to have this check in the driver, but it's better to do this
in mac80211 instead.
Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HT management is done differently for AP and STA modes, unify
to just the ->config() callback since HT is fundamentally a
PHY property and cannot be per-BSS.
Rename enum nl80211_sec_chan_offset as nl80211_channel_type to denote
the channel type ( NO_HT, HT20, HT40+, HT40- ).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unneeded member (skbuff) from
ieee80211_ibss_add_sta() method in its declaration (in ieee80211_i.h)
and its callers (in rx.c and mlme.c)
This patch removes unneeded member from struct ieee80211_rx_data
in ieee80211_i.h.
(Originally posted as two patches. -- JWL)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds new NL80211_CMD_SET_WIPHY attributes
NL80211_ATTR_WIPHY_FREQ and NL80211_ATTR_WIPHY_SEC_CHAN_OFFSET to allow
userspace to set the operating channel (e.g., hostapd for AP mode).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the SSID from the driver API since now there is no
driver that requires knowing the SSID and I think it's
unlikely that any hardware design that does require the
SSID will play well with mac80211.
This also removes support for setting the SSID in master
mode which will require a patch to hostapd to not try.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The two new commands are NL80211_CMD_GET_MESH_PARAMS and
NL80211_CMD_SET_MESH_PARAMS. There is a new attribute enum,
NL80211_ATTR_MESH_PARAMS, which enumerates the various mesh configuration
parameters.
Moved struct mesh_config from mac80211/ieee80211_i.h to net/cfg80211.h.
nl80211_get_mesh_params and nl80211_set_mesh_params unpack the netlink messages
and ask the driver to get or set the configuration. This is done via two new
function stubs, get_mesh_params and set_mesh_params, in struct cfg80211_ops.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So after the previous changes we were still unhappy with how
convoluted the API is and decided to make things simpler for
everybody. This completely changes the rate control API, now
taking into account 802.11n with MCS rates and more control,
most drivers don't support that though.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HT handling has the following deficiencies, which I've
(partially) fixed:
* it always uses the AP info even if there is no AP,
hence has no chance of working as an AP
* it pretends to be HW config, but really is per-BSS
* channel sanity checking is left to the drivers
* it generally lets the driver control too much
HT enabling is still wrong with this patch if you have more than
one virtual STA mode interface, but that never happens currently.
Once WDS, IBSS or AP/VLAN gets HT capabilities, it will also be
wrong, see the comment in ieee80211_enable_ht().
Additionally, this fixes a number of bugs:
* mac80211: ieee80211_set_disassoc doesn't notify the driver any
more since the refactoring
* iwl-agn-rs: always uses the HT capabilities from the wrong stuff
mac80211 gives it rather than the actual peer STA
* ath9k: a number of bugs resulting from the broken HT API
I'm not entirely happy with putting the HT capabilities into
struct ieee80211_sta as restricted to our own HT TX capabilities,
but I see no cleaner solution for now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move bss_conf into the vif struct so that drivers can
access it during ->tx without having to store it in
the private data or similar. No driver updates because
this is only for when they want to start using it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of having a separate callback, use the HW config callback
with a new flag to change retry limits.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I've come to think that not providing sequence numbers for
the normal STA mode case was a mistake, at least two drivers
now had to implement code they wouldn't otherwise need, and
I believe at76_usb and adm8211 might be broken.
This patch makes mac80211 assign a sequence number to all
those frames that need one except beacons. That means that
if a driver only implements modes that do not do beaconing
it need not worry about the sequence number.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 notify the driver which configuration
actually changed, e.g. channel etc.
No driver changes, this is just plumbing, driver authors are
expected to act on this if they want to.
Also remove the HW CONFIG debug printk, it's incorrect, often
we configure something else.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleans up a number of things:
* the unusable definition of the HT capabilities/HT information
information elements
* variable names that are hard to understand
* mac80211: move ieee80211_handle_ht to ht.c and remove the unused
enable_ht parameter
* mac80211: fix bug with MCS rate 32 in ieee80211_handle_ht
* mac80211: fix bug with casting the result of ieee80211_bss_get_ie
to an information element _contents_ rather than the
whole element, add size checking (another out-of-bounds
access bug fixed!)
* mac80211: remove some unused return values in favour of BUG_ON
checking
* a few minor other things
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes unused definition of struct sta_attribute
in net/mac80211/ieee80211_i.h.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no checking that the HT IEs are of the right length
which can be used by an attacker to cause an out-of-bounds
access by sending a too short HT information/capability IE.
Fix it by simply pretending those IEs didn't exist when too
short.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Long awaited, hard work. This patch totally cleans up the rate control
API to remove the requirement to include internal headers outside of
net/mac80211/.
There's one internal use in the PID algorithm left for mesh networking,
we'll have to figure out a way to clean that one up and decide how to
do the peer link evaluation, possibly independent of the rate control
algorithm or via new API.
Additionally, ath9k is left using the cross-inclusion hack for now, we
will add new API where necessary to make this work properly, but right
now I'm not expert enough to do it. It's still off better than before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to register the master netdev with cfg80211,
in fact, this is quite dangerous and lead to having to add
checks for the master interface all over the config handlers.
This patch removes the "ieee80211_ptr" from the master iface
in favour of having a small netdev_priv() associated with
the master interface that stores the ieee80211_local pointer.
Because of this, a lot of code in the configuration handlers
can go away. To make this patch easier to verify I have also
removed a number of wiphy_priv() calls in favour of getting
the sdata first and then the local pointer from that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon counters mac80211 keeps are only used for debugfs,
unfortunately, they are incorrect for many hardware designs,
namely any design that has a beacon template. Hence, remove the
counters so we don't create the impression they are usable.
This also allows removing the beacon MESH #ifdef again.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the code to handle regular interfaces out of main.c and
into iface.c, keep only the master interface stuff in main.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's really no reason for mac80211 to be using its
own interface type defines. Use the nl80211 types and
simplify the configuration code a bit: there's no need
to translate them any more now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers need to know the basic rateset to be able to configure
the ACK/CTS programming in hardware correctly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some comments refer to 80211.o or similar; also remove
a comment about implementing fragments better, we really
have better things to do.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most of the scan functions are called ieee80211_sta_scan_*
or similar, make clean it up so they are all just called
ieee80211_scan_*.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bridge_packets configuration really should be per virtual
interface (theoretically per AP/VLAN, but this is much easier);
there currently is no way to set it yet though. Also invert
the option to "NO_BRIDGE_PACKETS" so the default is to bridge.
While at it, also document the flags properly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It really doesn't belong into the wireless extensions code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This way all the utility functions are at the top, then the
state machine and externally callable functions are moved to
the bottom. Also clean up ieee80211_i.h a bit and add a few
comments about which functions are called from where.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch splits off mesh handling from the STA/IBSS.
Unfortunately it increases mesh code size a bit, but I
think it makes things clearer. The patch also reduces
per-interface run-time memory usage.
Also clean up a few places where ifdef is not required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ieee80211_sta_tx function isn't MLME code any more,
it's getting used by a lot of code. Move it to utils and
rename it to ieee80211_tx_skb.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Like the HT code, this doesn't depend on the STA-mode implementation
and can be handled entirely independently. There's only stub code
for now, but when it gets filled having it in its own file will be
beneficial.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The aggregation handling isn't dependent on anything related to our
STA-mode implementation, and doesn't need to depend on it for frame
processing. This patch moves the relevant code to ht.c and adds a
hook in rx.c. For now, the relevant action frames are only processed
in STA/IBSS modes, but that's now something we can easily change.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hardware is started it might be in a confused state with
respect to queue QoS parameters. This patch changes mac80211
to set sane defaults right after the hardware is brought up.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves all the BSS list handling out of mlme.c to scan.c,
no further changes except fixing kzalloc/atomic_inc/atomic_inc
to kzalloc/atomic_set(2).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch refactors some code and moves the scan RX function
to scan.c. More importantly, however, it changes it so that the
MLME's beacon/probe_resp functions aren't invoked when scanning
so that we can remove a "if (scanning)" conditions from two
places.
There's a very slight behavioural change in this patch: now,
when scanning, IBSS and mesh aren't updated even on the same
channel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here's a first patch to move some code from mlme.c to a
new file called scan.c. The end result will hopefully be
a more manageable mlme.c.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now use sdata pointers most of the time, using a netdev
pointer here is somewhat artificial, use an sdata pointer instead.
Replace a netdev-prefix in a few messages by a wiphy-prefix.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
debugfs union in struct ieee80211_sub_if_data is misused by including a
common default_key dentry as a union member. This ends occupying the same
memory area with the first dentry in other union members (structures;
usually drop_unencrypted). Consequently, debugfs operations on
default_key symlinks and drop_unencrypted entry are using the same
dentry pointer even though they are supposed to be separate ones. This
can lead to removing entries incorrectly or potentially leaving
something behind since one of the dentry pointers gets lost.
Fix this by moving the default_key dentry to a new struct
(common_debugfs) that contains dentries (more to be added in future)
that are shared by all vif types. The debugfs union must only be used
for vif type-specific entries to avoid this type of pointer corruption.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean up and extend scan result processing by storing all the IEs from
Beacon/Probe Response frames in a single block instead of allocating
memory for each specific IE separately. This removes lot of unnecessary
code and automatically supports reporting of new IEs (e.g., IEEE
802.11r) into user space without need to manually extend mac80211
scanning code whenever a new protocol adds IE(s).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previous version was using incorrect union structures for non-AP
interfaces when adding and removing max_ratectrl_rateidx and
force_unicast_rateidx entries. Depending on the vif type, this ended
up in corrupting debugfs entries since the dentries inside different
union structures ended up going being on top of eachother.. As the
end result, debugfs files were being left behind with references to
freed data (instant kernel oops on access) and directories were not
removed properly when unloading mac80211 drivers. This patch fixes
those issues by using only a single union structure based on the vif
type.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a direct probe request as first step in the association
flow if data we have is not up to date. Motivation of this step is to make
sure that the bss information we have is correct, since last scan could
have been done a while ago, and beacons do not fully answer this need as
there are potential differences between them and probe responses (e.g.
WMM parameter element)
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes noticed problem in noisy environments of 50+ APs
that scan fails to find the requested AP on first try, which
leads to connection refusal. second scan has empirically proven to fix
this problem in almost all cases.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Esti Kummer <ester.kummer@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch move add STA_MLME to station mlme state defines.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch replaces net_device arguments to mac80211 internal functions
with ieee80211_{local,sub_if_data} as appropriate.
It also does the same for many 802.11s mesh functions, and changes the
mesh path table to be indexed on sub_if_data rather than net_device.
If the mesh part needs to be a separate patch let me know, but since
mesh uses a lot of mac80211 functions which were being converted anyway,
the changes go hand-in-hand somewhat.
This patch probably does not convert all the functions which could be
converted, but it is a large chunk and followup patches will be
provided.
Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ETH_P_PAE belongs in if_ether.h with the other ETH_P_* definitions. This
patch moves it there.
Signed-off-by: Jasper Bryant-Greene <jasper@amiton.co.nz>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds the dtim_period in ieee80211_bss_conf, this allows the low
level driver to know the dtim_period, and to plan power save accordingly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch make mac80211 transmit correctly fragmented packet after
queue was stopped
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo