Move allocation after first check and fix memory leak.
Noticed-by: Daniel Marjamäki <danielm77@spray.se>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch ensures that the xc5000 will have firmware loaded as needed if the
part is powered down or reset via gpio from the host. An example of this, in
some cases, could be after the system resumes from standby or hibernate modes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This decreases scan time in Queens, New York from 28 minutes to 7 minutes,
with the exact same services found.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDIOC_ENUMSTD did not return all the PAL/SECAM/NTSC variants: it just returned
one single PAL/SECAM/NTSC standard without separate entries for the trickier
standards like NTSC-JP.
Changed the code so that it behaves better.
Also simplified the if/switch statements into a common standards lookup table.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix uncorrected block counter and bit error rate to follow DVB API spec:
- Unsupported controls return -ENOSYS.
- UNC must never be set to 0.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the i2c write fails during initialisation, an oops happens
because state->frontend.dvb is still undefined. Fixed.
Thanks to Sigmund Augdal for reporting this bug,
and to Hartmut Birr for suggesting the fix.
Thanks-to: Sigmund Augdal <sigmund@snap.tv>
Thanks-to: Hartmut Birr <e9hack@gmail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Fix S-Video and Compsite input settings for the Yuan MPC718 per user
reports from Yuri Warczynski <Yuri.Warczynski@gmail.com> and
Brian Hope <brian@hopefamily.info> and enable the card entry. The tuner reset
GPIO pin is likely incorrect as the tuner firmware cannot be reloaded without a
reboot. It is likely the audio routing is done via GPIO which is not
implemented yet, as users report audio doesn't work for some inputs.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18: Add I2C slave reset via GPIO upon initialization. One user,
Michael <msd4824@yahoo.com>, has reported this allows his HVR-1600 EEPROM to
be consistently recognized when using (long,) 100 msec delays. The delays in
this commit are nominal (10 & 40 msec) and need testing/tuning on boards with
I2C problems to find the right values.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a fix for the case when a digital capture from dvr0 happens first after
modprobe, before access to any cx18 v4l2 device nodes. The initial dvb feed
start has been changed to load the firmware if not already loaded. Also fixed a
use counter to correct dvb feed accounting if starting the transport DMA fails.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the cx18-cards.c structures for the HVR-1600 to reflect that audio Line In 2
and FM radio audio go to AIN3 and AIN4 of the CS5345 mux respectively. Verified
by physical inspection of an HVR-1600MCE, by listening to FM broadcasts with the
HVR-1600MCE, and by comparing with the card definition for a PVR-150 in ivtv.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change the cx18-av-core code so that accesses to cx23418 av core that
cause auto-configuration will be adjusted to emulate the auto-configuration
behavior of the cx25843. This fixes the VBI displayed as video at the top of
the frame for NTSC and probably other things.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The automatic Kconfig selection for tuners and frontends should be
conditional, based on !DVB_FE_CUSTOMISE.
This patch corrects the selection for VIDEO_CX18 on
MEDIA_TUNER_MXL5005S and DVB_S5H1409
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the current modulation and frequency is already set to
the desired parameters, then don't re-tune.
Don't store current frequency until after we've tuned successfully.
Force a re-tune after resume from standby.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the umt-010 driver the struct umt_properties sets the number of URBs for
transfer to 20. But in dvb-usb.h MAX_NO_URBS_FOR_DATA_STREAM is set to 10.
Not surprisingly this causes an oops for all devices which use the umt-010
chipset when they are inserted.
fix on Kaffeine channel scan for
Initialize stream count using MAX_NO_URBS_FOR_DATA_STREAM.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Devices can either be class devices or bus devices, not both at the
same time. Soc-camera host devices usually have a platform device as
their parent. Trying to also register them with a class crashes the
kernel, when linked statically. Interestingly, it works when built
as a module. Thanks to Paulius Zaleckas for reporting.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
platform_get_irq() returns a negative value on error, not 0.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Having the thermometer on during channel configuration
could cause tuning instability.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The TDA18271HD/C1 rf_cal map lookup is expected to go out of range outside
of the frequency window 41 MHz - 61.1 MHz. In these cases, the internal
RF tracking filters calibration mechanism is used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The IF notch bit gets unset when we update the Main Post Div register
value, before we have a chance to write the desired IF notch setting
to the tuner. Move the IF notch configuration to after we update MPD.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When an error occurs at firmware loading, sometimes, tda1004x stops answering.
Instead of reporting such error, attach code were assuming that the device were
answering an invalid ID (0xff). This can be seen when enabling debug options:
tda1004x: tda1004x_read_byte: reg=0x0
tda1004x: tda1004x_read_byte: error reg=0x0, ret=-5
Now, instead of reporting an invalid ID, it will report the correct error:
tda10046: chip is not answering. Giving up.
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
A possible improvement would be trying to reset the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A fresh copy of v.29 firmware, using get_firmware, is leading to an invalid
firmware:
DVB: registering new adapter (saa7133[0])
DVB: registering frontend 0 (Philips TDA10046H DVB-T)...
tda1004x: setting up plls for 48MHz sampling clock
tda1004x: found firmware revision ff -- invalid
tda1004x: trying to boot from eeprom
tda1004x: found firmware revision ff -- invalid
tda1004x: waiting for firmware upload...
tda1004x: Error during firmware upload
tda1004x: found firmware revision ff -- invalid
tda1004x: firmware upload failed
Sometimes, loading/unloading this firmware makes tda1004x to return an invalid
ID. However, there were no printk messages to help to identify what were the
cause for the error.
With this patch, it will now print:
Invalid tda1004x ID = 0xff. Can't proceed
saa7133[0]/dvb: failed to attach tda10046
saa7133[0]/dvb: frontend initialization failed
Tested with LifeView FlyDVB-T Hybrid Cardbus/MSI TV @nywhere A/D NB
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Describe exactly that only s-video and composite input are working on Avermedia
A700
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
decrementing dev->empress_users should be done as last action of ts_release,
because it sleeps and write access to dev->empress_started is not protected
in any way
(additionally closing thread could mute audio after opening thread unmuted it)
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-audio.c
em28xx-dvb.c
- Em28xx extensions should ensure they are being only loaded against devices
that support them. Deals with case where there are multiple em28xx
devices, some of which have DVB (or ALSA) support and some do not.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-cards.c
- DVB support is supposed to be enabled for the first generation HVR-900.
This device was confirmed with DVB by mkrufky when we did the original work
in April, but I guess we forgot to set the flag.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-video.c
- Properly handle loading of the module when multiple devices are already
connected (such as at bootup). Before we were only calling dvb_init()
against the last device in the list, so while we were handling subsequent
adds properly, if there were multiple devices present on driver load,
everybody except the last device would not get initialized.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx18-cards.h had a copy of the audio and video input enums
from cx18-av-core.h, but with different prefixes. Removed
that copy and used the ones from cx18-av-core.h.
Thanks to Andy Walls <awalls@radix.net> for the report.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The S-Video LUMA input was restricted to the In1-In4 inputs, but it
turns out that it can use the full range of In1-In8.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to timf <timf@iinet.net.au> and Mike Galbraith <efault@gmx.de> to report
this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch is based on work done by Madhvesh. R. Sulibhavi back in
March 2007.
We refactor some of the single step handling since it differs between
"classic" and "booke" powerpc cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Mark __flush_icache_range as a function that can't be probed since its
used by the kprobe code.
* Fix an issue with single stepping and async exceptions. We need to
ensure that we dont get an async exception (external, decrementer, etc)
while we are attempting to single step the probe point.
Added a check to ensure we only handle a single step if its really
intended for the instruction in question.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It was discussed that global arch_initcall() is preferred way to probe
QE GPIOs, so let's use it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Ports B and C pins programming is changed to get SCC2 UART and FCC3
ethernet work.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that arch/ppc is gone we always define CONFIG_PPC_CPM_NEW_BINDING so
we can remove all the code associated with !CONFIG_PPC_CPM_NEW_BINDING.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that arch/ppc is gone we always define CONFIG_PPC_CPM_NEW_BINDING so
we can remove all the code associated with !CONFIG_PPC_CPM_NEW_BINDING.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we have an L2CSR register (e500mc) we need to flush the L2 before going
to nap. We use the HW flush mechanism provided in that register.
The code reuses the CPU_FTR_604_PERF_MON bit as it is no longer used by
any code in the kernel. Additionally we didn't reuse the exist L2CR
feature bit as this is intended for the 7xxx L2CR register and L2CSR
is part of the new Freescale "Book-E" registers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The e500 core enter DOZE/NAP power-saving modes when the core go to
cpu_idle routine.
The power management default running mode is DOZE, If the user
echo 1 > /proc/sys/kernel/powersave-nap
the system will change to NAP running mode.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Marcin Slusarz