In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Apart from the regular AM18x/DA850/OMAP-L138 SoC operating
at 300MHz, these SoCs have variants that can operate at a
maximum of 456MHz. Variants at 408Mhz and 375 Mhz are available
as well.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
The EVM hardware for all these variants is the same (except
for the actual SoC populated).
U-Boot on the EVM sets up ATAG_REVISION to inform the OS
regarding the speed grade supported by the silicon. We use
this information to pass on the speed grade information to
the SoC code.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
AM18x/DA850/OMAP-L138 SoCs have variants that can operate
at a maximum of 456 MHz at 1.3V operating point. Also the
1.2V operating point has a variant that can support a maximum
of 375 MHz.
This patch adds three new OPPs (456 MHz, 408 MHz and 372 MHz)
to the list of DA850 OPPs.
Not all silicon is qualified to run at higher speeds and
unfortunately the maximum speed the chip can support can only
be determined from the label on the package (not software
readable).
Because of this, we depend on the maximum speed grade information
to be provided to us in some board specific way. The board informs
the maximum speed grade information by setting the da850_max_speed
variable.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Use the mach-davinci/Kconfig to enable gpio-keys-polled as default when
da850-evm machine is enabled.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: "Nori, Sekhar" <nsekhar@ti.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a pca953x platform device for the tca6416 found on the evm
baseboard. The tca6416 is a GPIO expander, also found on the UI board at a
separate I2C address. The pins of the baseboard IO expander are connected to
software reset, deep sleep enable, test points, a push button, DIP switches and
LEDs.
Add support for the push button, DIP switches and LEDs and test points (as
free GPIOs). The reset and deep sleep enable connections are reserved by the
setup routine so that userspace can't toggle those lines.
The existing tca6416-keypad driver was not employed because there was no
apararent way to register the LEDs connected to gpio's on the tca6416 while
simultaneously registering the tca6416-keypad instance.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
CC: Govindarajan, Sriramakrishnan <srk@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The setup and teardown methods of the UI expander reference the SEL_{A,B,C}
pins by 'magic number' in each function. This uses the common enum for their offsets
in the expander setup and teardown functions.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Victor Rodriguez <vm.rod25@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds EV_KEYs for each of the 8 pushbuttons on the UI board via a
gpio-key device.
The expander is a tca6416; it controls the SEL_{A,B,C} lines which enable and
disable the peripherals found on the UI board in addition to the 8 pushbuttons
mentioned above. The reason the existing tca6416-keypad driver is not employed
is because there was no aparent way to keep the gpio lines used as
SEL_{A,B,C} registered while simultaneously registering the pushbuttons as a
tca6416-keypad instance.
Some experimentation with the polling interval was performed; we were searching
for the largest polling interval that did not affect the feel of the
responsiveness of the buttons. It is very subjective but 200ms seems to be a
good value that accepts firm pushes but rejects very light ones. The key values
assigned to the buttons were arbitrarily chosen to be F1-F8.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
CC: Govindarajan, Sriramakrishnan <srk@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Commit fcf173e451 (usb: musb: add names for IRQs
in structure resource) forgot to assign name to the DA8xx MUSB IRQ resource.
Because of that MUSB driver fails to load on DA8xx machines.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Ensure that the at24 eeprom driver is selected for certain boards that
need boot data (e.g. MAC address) from EEPROM.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There was a single case of 'da850evm' prefix in the board-da850-evm.c file
where the reset of the prefixes were 'da850_evm'; change it to 'da850_evm' for
consistency.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Change the mach-davinci Kconfig file so that GPIO_PCA953X is default when
MACH_DAVINCI_DA850_EVM is set instead of always selecting. This allows users
to compile pca953x as a module.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sergei Shtylyov <sshtylyov@mvista.com>
CC: Nori, Sekhar <nsekhar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When the RMII PHY on the UI board is enabled with CONFIG_DA850_UI_RMII
then then following will be printed to the console when warnings are
also enabled:
WARNING: at drivers/gpio/gpiolib.c:1567 __gpio_set_value+0x4c/0x5c()
Modules linked in:
[<c002c6ac>] (unwind_backtrace+0x0/0xf8) from [<c003b48c>] (warn_slowpath_common+0x4c/0x64)
[<c003b48c>] (warn_slowpath_common+0x4c/0x64) from [<c003b4c0>] (warn_slowpath_null+0x1c/0x24)
[<c003b4c0>] (warn_slowpath_null+0x1c/0x24) from [<c01aed60>] (__gpio_set_value+0x4c/0x5c)
[<c01aed60>] (__gpio_set_value+0x4c/0x5c) from [<c0033bd4>] (da850_evm_ui_expander_setup+0x1e4/0x2
44)
[<c0033bd4>] (da850_evm_ui_expander_setup+0x1e4/0x244) from [<c02e2e1c>] (pca953x_probe+0x1f8/0x29
0)
<snip>
Traced the WARN_ON to the gpio_set_value(rmii_sel,0) call in
da850_evm_setup_emac_rmii. Replacing the call with the _cansleep variant
results in no more warning. Also replacing the gpio_set_value calls in the
teardown function.
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Chris Cordahi <christophercordahi@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
aemif_calc_rate() can return a negative error value, so all the
variables that get tested for this value need to be signed.
The maximum bit width of WSETUP(WSETUP_MAX) appears to be 30 bits
(0xf << 26). Using a signed instead of an unsigned integer
shouldn't make a difference here.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
A common do-while loop can be factored out from the end of
the branches.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch applies the following modifications to the tnetv107x clock tree:
- reparent tnetv107x usb clocks to usbss
- mark timer1 as always enabled
- enable set_rate on pll divider output clocks
- adjust tnetv107x tsc sysclk rate lower to fix invalid reset defaults
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch modifies the sysclk rate setting code to use the divider mask
specified in pll_data. Without this, devices with different divider ranges
(e.g. tnetv107x) fail.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Overwrite the default implementation of sched_clock that is based on
jiffies by something more precise. This improves timestamps in ftrace.
Implementation is copied from OMAP platform code.
Signed-off-by: Andreas Gaeer <Andreas.Gaer@baslerweb.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Defining iounmap() with arguments prevents it from being used as a
function pointer, causing platforms to work around this. Instead,
define it to be a simple macro.
Do the same for __arch_io(re|un)map too.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Soon resource data will get automatically
populated from a set of autogenerated data
from TI's hardware database for the OMAP
platform.
Such database, might not have resources at
the expected order by the current drivers.
While we could hack in some exceptions to
that tool to generate resources in a specific
order, it seems less fragile to use the
resource name instead. That way, no matter
what order the resources are generated, the
driver still work.
Modified the OMAP, Blackfin and Davinci
architecture files to add the name of the IRQs
in the resource structures and musb driver to
use the platform_get_irq_byname() api to get
the device and dma irq numbers instead of using
the index.
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add comments describing the platform data members
and per-chip-select SPI configuration structure.
Also, add some comments describing the what happens
during the driver probe.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The "clk_internal" platform data member which contols the
CLKMOD bit in Global Control Register 1 is not useful
since CLKMOD needs be set to 1 *always* to ensure master
mode operation.
Remove this platform data.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Let DMA operation be specified on a per-device basis instead
of selecting it once during probe.
A side effect of this is the need to combine the PIO and DMA buffer
txrx_bufs routine. This is good since they anyway share some common
functionality.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Do not allocate (and de-allocate) SPI DMA channels during setup
(and cleanup) for each SPI device. Instead, allocate the DMA
channels once duing probe and use them for the life time of
the driver.
This makes sense since there are dedicated DMA channels meant
for SPI use.
This also helps remove the unnecessary DMA "sync_dev" variables
being used to store DMA channel information.
Also, the "use_dma" platform variable is now eliminated since
it is possible to check if the platform supports DMA or not
based upon whether DMA resources can be found or not.
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Tested-By: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Due to the full duplex nature of the SPI bus, the SPI master
on DaVinci needs transmit to be active even if the tranfer is
only meant to collect receive data.
The current code achieves this by using a temporary zeroed buffer
to provide DMA data in case the transfer does not have a transmit
buffer provided.
However, the transmit DMA is started only if transmit buffer is
provided rendering the temporary buffer unused. Instead the code
relies on a write to SPIDAT1 register to trigger transmit operation.
This however only sends two bytes of data.
Fix this by starting transmit DMA always.
This changes exposes a bug on DM355 where the CSHOLD bit in
SPIDAT1 needs to be written to in between transfers. Handle
that by introducing a "cshold_bug" platform data which is
set to true for DM355.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for SPI interrupt mode operation.
Define a per chip-select "io type" variable which
specifies if the transfers on this chip-select should
happen in interrupt mode or polled mode.
Introduce a new function davinci_spi_process_events()
to help consolidate the code between interrupt mode
processing and polled mode processing.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The interrupt mode support as it stands is another version
of poll mode. Even when interrupt mode is selected, the code
tight loops on interrupt status register, rendering it totally
useless. A completion variable is initialized, but never used.
Remove this fake interrupt mode since users can anyway use
poll mode with no functional difference. A usefully implemented
interrupt mode support can be added later.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Just enabling WAITENA in SPIFMTn register waits for the
enable signal from the slave indefinitely. Allow support
for finite waiting by adding support for c2e delay
(maximum time for addressed slave to respond) and t2e
delay (maximum time for slave to respond after transmit
data finished).
While at it, modify the T2C and C2T defines by prepending
the register name as is the convention followed for other
register field elsewhere in the driver.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Some chip-select specific paramterers like wdelay, parity, usage of
chip-select timers (and the actual timer values) are included in
platform data forcing the same behaviour across all chip-selects.
Create a new davinci_spi_config data structure which can be passed
along using controller_data member of spi_device data structure
on a per-device basis.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The SPI_READY bit of struct spi_device:mode serves the purpose
of letting the SPI master know if the slave can signal if it is
ready for transfer or not.
The 'wait_enable' platform data was duplicating this functionality.
Use the framework provided method of indicating this capability.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Sometimes, the chip selects provided by SPI module are
muxed with other functionality and cannot be used in
some designs. In such cases, it becomes convenient to use
an available GPIO line as chip select.
This patch enables the DaVinci SPI driver to treat specific
GPIO lines as chip selects based on information provided in
platform data.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Let davinci_spi_chipselect() perform both activation and
deactivation of chip selects. This lets spi_bitbang fully
control chip select activation, as intended by the SPI API.
With this change, the chip select activation code need not
be duplicated in davinci_spi_bufs_{pio|dma}().
Also, keeping chip select active control is removed as a
platform data and simply controlled using information from
spi_bitbang on whether chip slect should be activated or
de-activated.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Tested-By: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Multi-component commit f0fba2ad broke a few things which this patch should
fix. Tested on the DM355 EVM. I've been as careful as I can, but it would be
good if those with access to other Davinci boards could test.
--
The multi-component commit put the initialisation of
snd_soc_dai.[capture|playback]_dma_data into snd_soc_dai_ops.hw_params of the
McBSP, McASP & VCIF drivers (davinci-i2s.c, davinci-mcasp.c & davinci-vcif.c).
The initialisation had to be moved from the probe function in these drivers
because davinci_*_dai changed from snd_soc_dai to snd_soc_dai_driver.
Unfortunately, the DMA params pointer is needed by davinci_pcm_open (in
davinci-pcm.c) before hw_params is called. I have moved the initialisation to
a new snd_soc_dai_ops.startup function in each of these drivers. This fix
indicates that all platforms that use davinci-pcm must have been broken and
need to test with this fix.
--
The multi-component commit also changed the McBSP driver name from
"davinci-asp" to "davinci-i2s" in davinci-i2s.c without updating the board
level references to the driver name. This change is understandable, as there
is a similarly named "davinci-mcasp" driver in davinci-mcasp.c.
There is probably no 'correct' name for this driver. The DM6446 datasheet
calls it the "ASP" and describes it as a "specialised McBSP". The DM355
datasheet calls it the "ASP" and describes it as a "specialised ASP". The
DM365 datasheet calls it the "McBSP". Rather than fix this problem by
reverting to "davinci-asp", I've elected to avoid future confusion with the
"davinci-mcasp" driver by changing it to "davinci-mcbsp", which is also
consistent with the names of the functions in the driver. There are other
fixes required, so it was never going to be as simple as a revert anyway.
--
The DM365 only has one McBSP port (of the McBSP platforms, only the DM355 has
2 ports), so I've changed the the id of the platform_device from 0 to -1.
--
In davinci-evm.c, the DM6446 EVM can no longer share a snd_soc_dai_link
structure with the DM355 EVM as they use different cpu DAI names (the DM355
has 2 ports and the EVM uses the second port, but the DM6446 only has 1 port).
This also means that the 2 boards need different snd_soc_card structures.
--
The codec_name entries in davinci-evm.c didn't match the i2c ids in the board
files. I have only checked and fixed the details of the names used for the
McBSP based platforms. Someone with a McASP based platform (eg DA8xx) should
check the others.
Signed-off-by: Chris Paulson-Ellis <chris@edesix.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some boards that were added after the mass io_pgoffst/io_physio
removal, and were not updated in the original patch. Fixup here.
c.f. original io_pgoffst/io_physio removal
commit 6451d7783b
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Most of the regulator data structures are local to the
board file, but not made static. Fix this.
Also make the nand partition table static.
This gets rid of all the sparse warnings for this file.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On Davinci SRAM is mapped as MT_DEVICE becasue of the section
mapping pre-requisite instead of intended MT_MEMORY_NONCACHED
Since the section mapping limitation gets fixed with first
patch in this series, the MT_MEMORY_NONCACHED can be used now.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds initial support for the Hawkboard-L138 system
It is under the machine name "omapl138_hawkboard".
This system is based on the da850 davinci CPU architecture.
Information on these system may be found at http://www.hawkboard.org.
Basic support for the UART console is included in this patch.
It's tested with latest Angstrom File Systems like ramdisk
from http://alturl.com/imb45.
Signed-off-by: Victor Rodriguez <victor.rodriguez@sasken.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For the MityDSP-L138/MityARM-1808 SOMS, read the factory assigned
MAC address from the onboard I2C EPROM and assign it to the emac
device during platform initialization.
Signed-off-by: Michael Williamson <michael.williamson@criticallink.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a platform device definition for tnetv107x's touchscreen
controller.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds evm board specific keymap definitions and controller
configuration data for on-chip keypad controller on tnetv107x silicon.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds a platform device definition for tnetv107x's keypad
controller.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes davinci architecture code that has now been rendered
useless by the previous patches in the MDIO separation series.
In addition, the earlier phy_mask definitions have been replaced with
corresponding phy_id definitions.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Tested-by: Michael Williamson <michael.williamson@criticallink.com>
Tested-by: Caglar Akyuz <caglarakyuz@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Lennert Buytenhek