There's a really rare and obscure bug in CFQ, that causes a crash in
cfq_dispatch_insert() due to rq == NULL. One example of the resulting
oops is seen here:
http://lkml.org/lkml/2007/4/15/41
Neil correctly diagnosed the situation for how this can happen: if two
concurrent requests with the exact same sector number (due to direct IO
or aliasing between MD and the raw device access), the alias handling
will add the request to the sortlist, but next_rq remains NULL.
Read the more complete analysis at:
http://lkml.org/lkml/2007/4/25/57
This looks like it requires md to trigger, even though it should
potentially be possible to due with O_DIRECT (at least if you edit the
kernel and doctor some of the unplug calls).
The fix is to move the ->next_rq update to when we add a request to the
rbtree. Then we remove the possibility for a request to exist in the
rbtree code, but not have ->next_rq correctly updated.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We have a 10-15% performance regression for sequential writes on TCQ/NCQ
enabled drives in 2.6.21-rcX after the CFQ update went in. It has been
reported by Valerie Clement <valerie.clement@bull.net> and the Intel
testing folks. The regression is because of CFQ's now more aggressive
queue control, limiting the depth available to the device.
This patches fixes that regression by allowing a greater depth when only
one queue is busy. It has been tested to not impact sync-vs-async
workloads too much - we still do a lot better than 2.6.20.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert all this. It can cause device-mapper to receive a different major from
earlier kernels and it turns out that the Amanda backup program (via GNU tar,
apparently) checks major numbers on files when performing incremental backups.
Which is a bit broken of Amanda (or tar), but this feature isn't important
enough to justify the churn.
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Booting 2.6.21-rc3-g45592145 I noticed the following on one of my
machines in the bootlog:
io scheduler noop registered<6>Time: jiffies clocksource has been installed.
io scheduler deadline registered (default)
Looking at block/elevator.c, it appears that elv_register() uses two
consecutive printks in a non-atomic way, leading to the above glitch. The
attached trivial patch fixes this issue, by using a single printk.
Signed-off-by: Thibaut VARENE <varenet@parisc-linux.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
There is a small problem in handling page bounce.
At the moment blk_max_pfn equals max_pfn, which is in fact not maximum
possible _number_ of a page frame, but the _amount_ of page frames. For
example for the 32bit x86 node with 4Gb RAM, max_pfn = 0x100000, but not
0xFFFF.
request_queue structure has a member q->bounce_pfn and queue needs bounce
pages for the pages _above_ this limit. This routine is handled by
blk_queue_bounce(), where the following check is produced:
if (q->bounce_pfn >= blk_max_pfn)
return;
Assume, that a driver has set q->bounce_pfn to 0xFFFF, but blk_max_pfn
equals 0x10000. In such situation the check above fails and for each bio
we always fall down for iterating over pages tied to the bio.
I want to notice, that for quite a big range of device drivers (ide, md,
...) such problem doesn't happen because they use BLK_BOUNCE_ANY for
bounce_pfn. BLK_BOUNCE_ANY is defined as blk_max_pfn << PAGE_SHIFT, and
then the check above doesn't fail. But for other drivers, which obtain
reuired value from drivers, it fails. For example sata_nv uses
ATA_DMA_MASK or dev->dma_mask.
I propose to use (max_pfn - 1) for blk_max_pfn. And the same for
blk_max_low_pfn. The patch also cleanses some checks related with
bounce_pfn.
Signed-off-by: Vasily Tarasov <vtaras@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Several people have reported failures in dynamic major device number handling
due to the recent changes in there to avoid handing out the local/experimental
majors.
Rolf reports that this is due to a gcc-4.1.0 bug.
The patch refactors that code a lot in an attempt to provoke the compiler into
behaving.
Cc: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change I/O scheduler description to correctly show CFQ as being the default
scheduler and not the anticipatory scheduler that previously was default.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out in http://bugzilla.kernel.org/show_bug.cgi?id=7922, dynamic
blockdev major allocation can hand out majors which LANANA has defined as
being for local/experimental use.
Cc: Torben Mathiasen <device@lanana.org>
Cc: Greg KH <greg@kroah.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Tomas Klas <tomas.klas@mepatek.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently check the FIFO once per slice. Optimize that a bit and
only do it as the first thing for a new slice, so we don't end up
doing a single request and then seek to the FIFO requests.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It must always be the active queue, otherwise it's a bug. So just
use the active_queue, don't pass it in explicitly.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If a slice uses less than it is entitled to (or perhaps more), include
that in the decision on how much time to give it the next time it
gets serviced.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Right now we use slice_start, which gives async queues an unfair
advantage. Chance that to service_last, and base the resorter
on that.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Mathieu originally needed to add this for tracing Xen, but it's something
that's needed for any application that can be tracing while cpus are added.
unplug isn't supported by this patch. The thought was that at minumum a new
buffer needs to be added when a cpu comes up, but it wasn't worth the effort
to remove buffers on cpu down since they'd be freed soon anyway when the
channel was closed.
[zanussi@us.ibm.com: avoid lock_cpu_hotplug deadlock]
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Tom Zanussi <zanussi@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some partitioning systems create special partitions that
span the entire disk. One example are Sun partitions, and
this whole-disk partition exists to tell the firmware the
extent of the entire device so it can load the boot block
and do other things.
Such partitions should not be treated as normal partitions,
because all the other partitions overlap this whole-disk one.
So we'd see multiple instances of the same UUID etc. which
we do not want. udev and friends can thus search for this
'whole_disk' attribute and use it to decide to ignore the
partition.
Signed-off-by: Fabio Massimo Di Nitto <fabbione@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for raid5 to be sent a bio that is too big for an underlying
device. So if it is a READ that we pass stright down to a device, it will
fail and confuse RAID5.
So in 'chunk_aligned_read' we check that the bio fits within the parameters
for the target device and if it doesn't fit, fall back on reading through
the stripe cache and making lots of one-page requests.
Note that this is the earliest time we can check against the device because
earlier we don't have a lock on the device, so it could change underneath
us.
Also, the code for handling a retry through the cache when a read fails has
not been tested and was badly broken. This patch fixes that code.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Kai" <epimetreus@fastmail.fm>
Cc: <stable@suse.de>
Cc: <org@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 85e04e371b cleaned up the timeout
conversion, but did it exactly the wrong way. We get msecs from user
space, and should convert them into jiffies. Not the other way around.
Here is a fix with the overflow check sg.c has added in. This fixes DVD
burnign with Nero.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
[ "you'll be wanting a comma there" - Andrew ]
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A flag was recently added to the elevator code to avoid
performing an unplug when reuests are being re-queued.
The goal of this flag was to avoid a deep recursion that
can occur when re-queueing requests after a SCSI device/host
reset. See http://lkml.org/lkml/2006/5/17/254
However, that fix added the flag near the bottom of a case
statement, where an earlier break (in an if statement) could
transport one out of the case, without setting the flag.
This patch sets the flag earlier in the case statement.
I re-discovered the deep recursion recently during testing;
I was told that it was a known problem, and the fix to it was
in the kernel I was testing. Indeed it was ... but it didn't
fix the bug. With the patch below, I no longer see the bug.
Signed-off by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jens Axboe <axboe@suse.de>
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Two issues:
- The final return 1 should be a return 0, otherwise comparing cfqq is
a noop.
- bio_sync() only checks the sync flag, while rq_is_sync() checks both
for READ and sync. The latter is what we want. Expand the bio check
to include reads, and relax the restriction to allow merging of async
io into sync requests.
In the future we want to clean up the SYNC logic, right now it means
both sync request (such as READ and O_DIRECT WRITE) and unplug-on-issue.
Leave that for later.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The logic in cfq_allow_merge() wasn't clear enough - basically allow
merging for the same queues only. Do a fast check for 'rq and bio both
sync/async' before doing the cfqq hash lookup.
This is verified to work with the fixed elv_try_merge() from commit
bb4067e341.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent io scheduler allow_merge commit left the block layer with
no merging, oops. This patch fixes that up.
That means the CFQ change needs to be verified again, it might not fix
the original bug now. But that's a seperate thing, I'll double check
that tomorrow.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently we allow any merge, even if the io originates from different
processes. This can cause really bad starvation and unfairness, if those
ios happen to be synchronous (reads or direct writes).
So add a allow_merge hook to the io scheduler ops, so an io scheduler can
help decide whether a bio/process combination may be merged with an
existing request.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
The blk_rq_unmap_user() API is not very nice. It expects the caller to
know that rq->bio has to be reset to the original bio, and it will
silently do nothing if that is not done. Instead make it explicit that
we need to pass in the first bio, by expecting a bio argument.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If the bio is user copied, the copy back could return -EFAULT. Make
sure we return any error seen during unmapping.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We have full flexibility of merging parameters now, so we can remove the
hooks that define back/front/request merge strategies. Nobody is using
them anymore.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's a file system thing, for block requests the only size used in the
io paths is ->data_len as it is in bytes, not sectors.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We implemented the missing bits to allow this some time ago, and
they are integrated in AS. So remove the __module_get() to allow
the module to be unloaded.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
We need to do this, otherwise the io schedulers don't get access to the
sync flag. Then they cannot tell the difference between a regular write
and an O_DIRECT write, which can cause a performance loss.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When I converted the original patch, I left unnecessary blk_queue_bounce in
SG_IO.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch fixes bio leaks in SG_IO. rq->bio can be changed after io
completion, so we need to reset rq->bio before calling blk_rq_unmap_user()
http://marc.theaimsgroup.com/?l=linux-kernel&m=116570666807983&w=2
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
While working on bidi support at struct request level
I have found that blk_queue_activity_fn is actually never used.
The only user is in ide-probe.c with this code:
/* enable led activity for disk drives only */
if (drive->media == ide_disk && hwif->led_act)
blk_queue_activity_fn(q, hwif->led_act, drive);
And led_act is never initialized anywhere.
(Looking back at older kernels it was used in the PPC arch, but was removed around 2.6.18)
Unless it is all for future use off course.
(this patch is against linux-2.6-block.git as off 2006/12/4)
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Wire up read accounting for block devices, within submit_bio().
Cc: Jay Lan <jlan@sgi.com>
Cc: Shailabh Nagar <nagar@watson.ibm.com>
Cc: Balbir Singh <balbir@in.ibm.com>
Cc: Chris Sturtivant <csturtiv@sgi.com>
Cc: Tony Ernst <tee@sgi.com>
Cc: Guillaume Thouvenin <guillaume.thouvenin@bull.net>
Cc: David Wright <daw@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides fault-injection capability for disk IO.
Boot option:
fail_make_request=<probability>,<interval>,<space>,<times>
<interval> -- specifies the interval of failures.
<probability> -- specifies how often it should fail in percent.
<space> -- specifies the size of free space where disk IO can be issued
safely in bytes.
<times> -- specifies how many times failures may happen at most.
Debugfs:
/debug/fail_make_request/interval
/debug/fail_make_request/probability
/debug/fail_make_request/specifies
/debug/fail_make_request/times
Example:
fail_make_request=10,100,0,-1
echo 1 > /sys/blocks/hda/hda1/make-it-fail
generic_make_request() on /dev/hda1 fails once per 10 times.
Cc: Jens Axboe <axboe@suse.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the old complex and crufty bd_mutex annotation.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There was lots of #ifdef noise in the kernel due to hotcpu_notifier(fn,
prio) not correctly marking 'fn' as used in the !HOTPLUG_CPU case, and thus
generating compiler warnings of unused symbols, hence forcing people to add
#ifdefs.
the compiler can skip truly unused functions just fine:
text data bss dec hex filename
1624412 728710 3674856 6027978 5bfaca vmlinux.before
1624412 728710 3674856 6027978 5bfaca vmlinux.after
[akpm@osdl.org: topology.c fix]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch (as824b) makes percpu_free() ignore NULL arguments, as one would
expect for a deallocation routine. (Note that free_percpu is #defined as
percpu_free in include/linux/percpu.h.) A few callers are updated to remove
now-unneeded tests for NULL. A few other callers already seem to assume
that passing a NULL pointer to percpu_free() is okay!
The patch also removes an unnecessary NULL check in percpu_depopulate().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jens Axboe