PXA935 has changed its implementor ID from Intel to Marvell, this
patch modifies arch/arm/boot/compressed/head.S and proc-xsc3.S to
support a smooth bootup.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Commit 40df2d1d "[ARM] Update Xscale and Xscale3 PTE mappings" was
fingered by git-bisect for a boot failure on iop13xx. The change made
L_PTE_MT_WRITETHROUGH mappings L2-uncacheable. Russell points out that
this mapping is used for the vector page. Given the regression, and the
fact this page is used often, restore the old behaviour.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
As of the previous commit, MT_DEVICE_IXP2000 encodes to the same
PTE bit encoding as MT_DEVICE, so it's now redundant. Convert
MT_DEVICE_IXP2000 to use MT_DEVICE instead, and remove its aliases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are actually only four separate implementations of set_pte_ext.
Use assembler macros to insert code for these into the proc-*.S files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
(20072fd0c9 lost most of its changes
somehow, came from a mbox archive applied with git-am. No idea
what happened. This puts back the missing bits. --rmk)
The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.
This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.
CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:
a. _only_ PXA300/PXA310 support included and no L2 cache wanted
b. PXA320 support included, but want L2 be disabled
So the enabling of L2 depends on two things:
- CACHE_XSC3L2 is selected
- and L2 cache is present
Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).
IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.
Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:
- OC bits in TTBASE register (table walk outer cache attributes)
- LLR Outer Cache Attributes (OC) in Auxiliary Control Register
Signed-off-by: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The proc-*.S files have the _prefetch_abort pointer placed at the end
of the processor structure but the cpu-multi32.h defines it in the
second position. The patch also fixes the support for XSC3 and the
MMU-less CPUs (740, 7tdmi, 940, 946 and 9tdmi).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch cleans up proc-xsc3:
- Correct a number of typos.
- Fix up indentation in a number of places.
- Change references to the various caches to be more clear about
whether we're talking about the L1 D, the L1 I or the unified L2
cache.
- Rename "drain write buffer" to "data write barrier", the official
name used in the Manzano manual.
- Change the xsc3 cpu name from "XScale-Core3" to "XScale-V3 based
processor".
Also, since a previously merged patch implements proper support for
using a MAC or iWMMXt coprocessor on xsc3 platforms, we no longer
need to enable access to CP0 on boot.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Deepak Saxena has agreed to hand xsc3 maintainership over to me.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
L_PTE_ASID is not really required to be stored in every PTE, since we
can identify it via the address passed to set_pte_at(). So, create
set_pte_ext() which takes the address of the PTE to set, the Linux
PTE value, and the additional CPU PTE bits which aren't encoded in
the Linux PTE value.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove BTB_ENABLE from proc-xsc3.S
On some early revisions of xsc3 enabling the branch target buffer can cause
crashes, see erratum #42.
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge L_PTE_COHERENT with L_PTE_SHARED and free up a L_PTE_* bit.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These files want to provide/access ELF hwcap information, so should
be including asm/elf.h rather than asm/procinfo.h
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On some CPUs, bit 4 of section mappings means "update the
cache when written to". On others, this bit is required to
be one, and others it's required to be zero. Finally, on
ARMv6 and above, setting it turns on "no execute" and prevents
speculative prefetches.
With all these combinations, no one value fits all CPUs, so we
have to pick a value depending on the CPU type, and the area
we're mapping.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most MMU-based CPUs have a restriction on the setting of the data cache
enable and mmu enable bits in the control register, whereby if the data
cache is enabled, the MMU must also be enabled. Enabling the data
cache without the MMU is an invalid combination.
However, there are CPUs where the data cache can be enabled without the
MMU.
In order to allow these CPUs to take advantage of that, provide a
method whereby each proc-*.S file defines the control regsiter value
for use with nommu (with the MMU disabled.) Later on, when we add
support for enabling the MMU on these devices, we can adjust the
"crval" macro to also enable the data cache for nommu.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't enable the BTB on the ixp2350 as that can cause weird
crashes (erratum #42.) However, some bootloaders enable the BTB,
which means that we have to disable the BTB explicitly.
Found thanks to Tom Rini.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lennert Buytenhek
This patch adds support for the I/O coherent cache available on the
xsc3. The approach is to provide a simple API to determine whether the
chipset supports coherency by calling arch_is_coherent() and then
setting the appropriate system memory PTE and PMD bits. In addition,
we call this API on dma_alloc_coherent() and dma_map_single() calls.
A generic version exists that will compile out all the coherency-related
code that is not needed on the majority of ARM systems.
Note that we do not check for coherency in the dma_alloc_writecombine()
function as that still requires a special PTE setting. We also don't
touch dma_mmap_coherent() as that is a special ARM-only API that is by
definition only used on non-coherent system.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
Adapt xsc3 to the changes in 74945c8616
(xsc3 was written before but merged after the latter went in.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lennert Buytenhek
This patch adds support for the new XScale v3 core. This is an
ARMv5 ISA core with the following additions:
- L2 cache
- I/O coherency support (on select chipsets)
- Low-Locality Reference cache attributes (replaces mini-cache)
- Supersections (v6 compatible)
- 36-bit addressing (v6 compatible)
- Single instruction cache line clean/invalidate
- LRU cache replacement (vs round-robin)
I attempted to merge the XSC3 support into proc-xscale.S, but XSC3
cores have separate errata and have to handle things like L2, so it
is simpler to keep it separate.
L2 cache support is currently a build option because the L2 enable
bit must be set before we enable the MMU and there is no easy way to
capture command line parameters at this point.
There are still optimizations that can be done such as using LLR for
copypage (in theory using the exisiting mini-cache code) but those
can be addressed down the road.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eric Miao