Some PCMCIA cards do not mention specific IO addresses in the CIS. In that
case, inside the alloc_io_space function, conflicts are detected (the
function returns 1) for the second function of a multifunction card unless
the length of IO address range required is greater than 0x100.
The following patch will remove this conflict checking for a PCMCIA
function which had not mentioned any specific IO address to be mapped from.
The patch is tested for Linux kernel 2.6.15.4 and works fine in the above
case and is as suggested by Dave Hinds.
Signed-off-by: Kaustav Majumdar <kaustav.majumdar@wipro.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As a replacement for the broad manufactor/card ID match we commented out
because of conflicts with pcnet_cs, add two product ID matches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
More correct AT91 CF wakeup logic ... only enable/disable the IRQ wakeup
capability, not the IRQ itself. That way the we know that the IRQ will be
disabled correctly, in suspend/resume logic instead of ARM IRQ code.
Most of the pin multiplexing setup has moved to the devices.c setup code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This is a cross-port of a similar patch for aic7xxx;
only it's a bit simpler here as we don't support HVD
and all controller actually implement this register.
I hope.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a cross-port from aic79xx; we still hit the occasional
BUG_ON in slave_destroy. And again we don't really need the
slave_destroy callback nor the ahc_linux_target structure
at all.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
aic79xx has a special 'iocell' chip which handles the precompensation.
If it's set via DV we should make sure to set the chip correctly, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Whenever an external device is resetted we really have to take
care to keep the channel in sync. Just notifying SCSI-ML and retry
is not enough as we have to make sure the SCSI bus is not getting
confused, either.
So whenever we detect an external reset we rewrite the command to
TUR, disable packetized command and notify the internal engine
that an abort has happened. This way we trigger a proper bus
reset sequence and all devices will be renegotiated properly.
Kudos to Justin Gibbs and Luben Tuikov for this idea.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix printk format warning:
drivers/scsi/lpfc/lpfc_attr.c:597: warning: long long unsigned int format, uint64_t arg (arg 4)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- make needlessly global code static
- #if 0 the following unused global functions:
- aic79xx_core.c: ahd_print_scb
- aic79xx_core.c: ahd_suspend
- aic79xx_core.c: ahd_resume
- aic79xx_core.c: ahd_dump_scbs
- aic79xx_osm.c: ahd_softc_comp
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleanups done to use min/max macros from kernel.h. Handcrafted MIN/MAX
macros are changed to use macros in kernel.h
[akpm@osdl.org: fix warning]
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds support for REPORT TARGET PORT GROUPS. This is used
eg for the multipathing priority callout to determine the path
priority.
With this patch multipath-tools can use the existing mpath_prio_alua
callout to exercise the path priority grouping.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix typo in check of return value of qla1280_bus_reset() which would
result in an adapter reset in addition to the bus reset.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to the iscsi RFC, we cannot send other requests if
we have sent a logout pdu. This patch enforces this requirement
by blocking the session and suspending the send thread. Userspace
decides if we restart the connection or if we just free everything.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We have been dropping the pdu. We should just send it to userspace
and let it handle it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from bhalevy@gmail.com:
It looks like change 652 to libiscsi.c added some dead code around line
670
if (rc) {
spin_unlock_bh(&conn->session->lock);
goto again;
}
since 5 lines above we goto again if (rc).
It looks like the previous if (rc) should go away if we want to put the
ctask before
breaking out of the while loop with "goto again" (see following patch).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If connection creation fails we end up calling list_del
on a invalid struct. This then causes an oops. We are not
acutally using the lists (old MCS code we thought might
be useful elsewhere) so this patch just removes that
code.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The transport class recv mempools are causing slab corruption.
We could hack around netlink's lack of mempool support like dm,
but it is just too ulgy (dm's hack is ugly enough :) when you need
to support broadcast.
This patch removes the recv pools. We have not used them even when
we were allocting 20 MB per session and the system only had 64 MBs.
And we have no pools on the send side and have been ok there. When
Peter's work gets merged we can use that since the network guys
are in favor of that approach and are not going to add mempools
everywhere.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Doesn't make the hardware hot pluggable but does ensure the driver won't
crash when another device is hot-unplugged at the wrong moment. Soon I
propose to deprecate pci_find_device() and some of its friends.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Debugging TCQ issues has shown me this is a very useful parameter to be
able to view. Add it to he host class parameters.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
It is known that 2 LSI Logic MegaRAID SATA RAID Controllers (150-4 and
150-6) don't support 64-bit DMA. Unfortunately currently this check is
wrong and driver sets 64-bit DMA mode for these devices.
Signed-off-by: Andrey Mirkin <amirkin@sw.ru>
Acked-by: "Ju, Seokmann" <Seokmann.Ju@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add PCI id. Plus correct for possibly missing resistor that can cause
FLASHEX to have the wrong value.
Signed-off-by: Sergey Kononenko <sergk@sergk.org.ua>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The "ibmvscsi: treat busy and error conditions separately" patch
submitted by Dave Boutcher back in June incorrectly reenables the CRQ.
The broken logic causes the adapter to get disabled if the CRQ
connection happens to close temporarily. This patch "fixes that
obviously wrong logic check" (Dave's words).
Signed-off-by: Santiago Leon <santil@us.ibm.com>
Signed-off-by: David Boutcher <sleddog@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Drop queue-depths across all luns for a given fcport
during TASK_SET_FULL statuses.
- Ramp-up I/Os after throttling.
- Consolidate completion-status handling of CS_QUEUE_FULL with
CS_COMPLETE as ISP24xx firmware no longer reports
CS_QUEUE_FULL.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Early ISP2432 parts have a known hardware issue when coming
out of a D3 hot state. This issue can result in a hung PCIe
link. Recent firmwares contain a workaround whereby the
stop-firmware mailbox command prevents the ISP from entering
the D3 hot state.
In order to ensure that the workaround succeeded the driver
must verify that the stop-firmware mailbox command completes
successfully. In the event of a failure, the driver
attempts a shutdown-retry after resetting the ISP and
re-executing firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in the Fibre Channel
driver (fc4).
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete typedefd Scsi_Cmnd to struct scsi_cmnd in
the ninja scsi pcmcia driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Changes the obsolete Scsi_Cmnd to struct scsi_cmnd in psi240i-driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If we fail to allocate mp->virt during the first while loop iteration,
mlist is still uninitialized, therefore we should check if before
dereferencing.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes a typo in the aic7xxx_old.c.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Thanks to James Smart for the inspiration.
Stall error handler if attempting recovery while an rport is blocked.
This avoids device offline scenarios due to errors in the error handler.
Also verify that VirtDevice is available before issuing scsi command.
VirtDevice is removed when fc transport removes a target.
See James Smart's patch of 08/17/2006 for greater detail.
http://marc.theaimsgroup.com/?l=linux-scsi&m=115583213624803&w=2
Also bump version number per Eric's request.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: Eric Moore <eric.moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
According to the adaptec sources aic7xxx / aic79xx really can do
4MB transfers. So we should adjust .max_sectors.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There is a dup printk at the tail of qla4xxx_module_init(). Remove the
first instance as it's before the complete success of the function.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
AM53C974A's Start Transfer Counter register has 24 bits, thus
maximum transfer length is 16MiB. But the maximum I can test
is 8MiB, so use that until somebody tests 16MiB.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Based on the original patch from Hannes Reinecke <hare@suse.de>
Fix st_open() to return -ENOMEDIUM instead of -EIO if no medium is
found.
Signed-off-by: Kai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change obsolete Scsi_Cmnd to struct scsi_cmnd in the Qlocic FAS408 driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Change the obsolete Scsi_Cmnd to struct scsi_cmnd in the sun3-driver.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
All callers and the function itself dereference dinfo, so we can remove the
check. (coverity id #1371)
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only) to make sure the files are compiling without
any warning/error due to new changes
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
- callers of drm_sysfs_create() and drm_sysfs_device_add() looked for
errors using IS_ERR(), but the functions themselves only ever returned
NULL on error. Fixed.
- unwind from, and propagate sysfs errors
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The other failure returns in this function are negative, so make
this one do the same.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
CRYPTO_MANAGER is selected automatically by CONFIG_ECB and CONFIG_CBC.
config CRYPTO_ECB
tristate "ECB support"
select CRYPTO_BLKCIPHER
select CRYPTO_MANAGER
I've added CONFIG_ECB to the ones you mentioned and CONFIG_CBC to
gssapi.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Kaustav Majumdar