The Atmel AT91 and AVR32 processor architectures share many of the same
peripherals. The PDC (Peripheral Data Controller) registers are also
implemented within in a number of the on-chip peripherals (eg, USART,
MMC, SPI, SSC, etc).
In a attempt not to duplicate the register definitions in each
peripheral, or in each architecture, the at91_pdc.h header in
asm-arm/arch-at91 and asm-avr32/arch-at32ap has been replaced with
linux/atmel_pdc.h.
The definitions have also been renamed from AT91_PDC_* to ATMEL_PDC_*,
and the drivers updated accordingly.
Original patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many controllers have an upper limit on the number of blocks that can be
transferred in one request. Allow the host drivers to specify this and make
sure we avoid hitting this limit.
Also change the max_sectors field to avoid confusion. This makes it map
less directly to the block layer limits, but as they didn't apply directly
on MMC cards anyway, this isn't a great loss.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Most controllers have an upper limit on the block size. Allow the host
drivers to specify this and make sure we avoid hitting this limit.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Linker level tweaks for the AT91 MMC driver:
- fix a wrongly-exported symbol
- move probe() to init section
- move remove() to exit section
When this driver is statically linked, this patch shrinks the driver's
runtime I-space footprint by over 20% (950 bytes).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The driver is usable on the newer SAM9 processors so replace all text
references to AT91RM9200 with just AT91.
The controller bug where all the words are byte-swapped is fixed on the
AT91SAM9 processors. The byte-swapping work-around therefore only needs
to be done if cpu_is_at91rm9200().
[Original patch from Wojtek Kaniewski]
The AT91RM9200 and AT91SAM9260 processors support two MMC/SD slots - the
slot which is connected is now passed via the platform_data and the
correct slot selected in the AT91_MCI_SDCR register.
The driver should not be calling at91_set_gpio_output() since the VCC
pin should have already been configured as an output in the
processor/board setup code. The driver should call
at91_set_gpio_value().
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
A number of small cleanups to the AT91RM9200 MMC driver:
- fix warnings generated by pr_debug().
- prepend "AT91 MMC:" to printk() messages.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch simplifies the AT91RM9200 MMC interrupt handler code so that
it doesn't re-read the Interrupt Status and Interrupt Mask registers
multiple times.
Also defined AT91_MCI_ERRORS instead of using the hard-coded 0xffff0000.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move the global 'mci_clk' variable into the local 'at91mci_host'
structure.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Use the I/O base-address and IRQ passed to the driver via the
platform_device resources instead of using hardcoded values.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The I/O base address is now stored in the 'at91mci_host' structure. We
therefore have to pass this structure to at91_mci_read() and
at91_mci_write().
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Now that mmc_host_ops can be constified, update the various drivers
to constify those method tables and shrink the writable data segment.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
This patch updates the drivers (and other files) which include the
hardware headers. This fixes the breakage introduced in patches 3950/1
and 3951/1 (those patches were getting big).
The AVR32 architecture uses the same serial driver and had its own copy
of at91rm9200_pdc.h. Renamed it to at91_pdc.h
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This is more preparation for adding support for the new Atmel AT91SAM9
processors.
Changes include:
- Replace AT91_BASE_* with AT91RM9200_BASE_*
- Replace AT91_ID_* with AT91RM9200_ID_*
- ROM, SRAM and UHP address definitions moved to at91rm9200.h.
- The raw AT91_P[ABCD]_* definitions are now depreciated in favour of
the GPIO API.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some MMC hosts can only handle log2 block sizes. Unfortunately,
the MMC password support needs to be able to send non-log2 block
sizes. Provide a capability so that the MMC password support can
decide whether it should use this support or not.
The unfortunate side effect of this host limitation is that any
MMC card protected by a password which is not a log2 block size
can not be accessed on a host which only allows a log2 block size.
This change just adds the flag. The MMC password support code
needs updating to use it (if and when it is finally submitted.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch includes code cleanups and minor fixes to the AT91RM9200 MMC
driver.
1. Replace calls to DBG() with pr_debug().
2. 'host' can never be null, so don't bother checking for that case.
3. Remove SA_SAMPLE_RANDOM from request_irq(). [Patch from Matt
Mackall]
4. clk_get() doesn't return NULL on error - need to test returned value
with IS_ERR().
5. Free resources if clk_get() or request_irq() fails.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMC specification allows non-power of two block sizes. As such,
we should not pass the log2 block size to host drivers, but instead
pass the byte size.
However, ARM MMCI can only work with log2 block size, so continue to
pass both the log2 block size and byte block size. This means that
for the moment, the byte block size must remain a power of two, but
this is the first stage of removing this restriction for other hosts.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than having every driver duplicate the set_ios debugging,
provide a single version in mmc.c which can be expanded as we
add additional functionality.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Andrew Victor
This patch adds support for the MMC/SD card interface on the Atmel
AT91RM9200 processor.
Original driver was by Nick Randell, but a number of people have
subsequently worked on it. It's currently maintained by Malcolm Noyes.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrew Victor