This fixes a problem spotted with zebra, but not sure if it is
necessary a kernel problem. With IPV6 when an address is added to an
interface, Zebra creates a duplicate RIB entry, one as a connected
route, and other as a kernel route.
When an address is added to an interface the RTN_NEWADDR message
causes Zebra to create a connected route. In IPV4 when an address is
added to an interface a RTN_NEWROUTE message is set to user space with
the protocol RTPROT_KERNEL. Zebra ignores these messages, because it
already has the connected route.
The problem is that route created in IPV6 has route protocol ==
RTPROT_BOOT. Was this a design decision or a bug? This fixes it. Same
patch applies to both net-2.6 and stable.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipv6_dev_get_saddr() blindly de-references dst_dev to get the network
namespace, but some callers might pass NULL. Change callers to pass a
namespace pointer instead.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes legacy reinvent-the-wheel type thing. The generic
machinery integrates much better to automated debugging aids
such as kerneloops.org (and others), and is unambiguous due to
better naming. Non-intuively BUG_TRAP() is actually equal to
WARN_ON() rather than BUG_ON() though some might actually be
promoted to BUG_ON() but I left that to future.
I could make at least one BUILD_BUG_ON conversion.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following scenario:
ipv6_del_addr(ifp)
ipv6_ifa_notify(RTM_DELADDR, ifp)
ip6_del_rt(ifp->rt)
after returning from the ipv6_ifa_notify and enabling BH-s
back, but *before* calling the addrconf_del_timer the
ifp->timer fires and:
addrconf_dad_timer(ifp)
addrconf_dad_completed(ifp)
ipv6_ifa_notify(RTM_NEWADDR, ifp)
ip6_ins_rt(ifp->rt)
then return back to the ipv6_del_addr and:
in6_ifa_put(ifp)
inet6_ifa_finish_destroy(ifp)
dst_release(&ifp->rt->u.dst)
After this we have an ifp->rt inserted into fib6 lists, but
queued for gc, which in turn can result in oopses in the
fib6_run_gc. Maybe some other nasty things, but we caught
only the oops in gc so far.
The solution is to disarm the ifp->timer before flushing the
rt from it.
Signed-off-by: Andrey Vagin <avagin@parallels.com>
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
- If 0, disable DAD.
- If 1, perform DAD (default).
- If >1, perform DAD and disable IPv6 operation if DAD for MAC-based
link-local address has been failed (RFC4862 5.4.5).
We do not follow RFC4862 by default. Refer to the netdev thread entitled
"Linux IPv6 DAD not full conform to RFC 4862 ?"
http://www.spinics.net/lists/netdev/msg52027.html
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Check the type of the address when adding a new one on interface.
- the unspecified address (::) is always disallowed (RFC4291 2.5.2)
- the loopback address is disallowed unless the interface is (one of)
loopback (RFC4291 2.5.3).
- multicast addresses are disallowed.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Large Receive Offload (LRO) is only appropriate for packets that are
destined for the host, and should be disabled if received packets may be
forwarded. It can also confuse the GSO on output.
Add dev_disable_lro() function which uses the appropriate ethtool ops to
disable LRO if enabled.
Add calls to dev_disable_lro() in br_add_if() and functions that enable
IPv4 and IPv6 forwarding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pacth makes IPv6 address labels per network namespace.
It keeps the global label tables, ip6addrlbl_table, but
adds a 'net' member to each ip6addrlbl_entry.
This new member is taken into account when matching labels.
Changelog
=========
* v1: Initial version
* v2:
* Minize the penalty when network namespaces are not configured:
* the 'net' member is added only if CONFIG_NET_NS is
defined. This saves space when network namespaces are not
configured.
* 'net' value is retrieved with the inlined function
ip6addrlbl_net() that always return &init_net when
CONFIG_NET_NS is not defined.
* 'net' member in ip6addrlbl_entry renamed to the less generic
'lbl_net' name (helps code search).
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
This inline function, for readability, returns if the route
is a "prefix" route regardless if it was installed by RA or by
hand.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
- Allow longer lifetimes (>= 0x7fffffff/HZ) on 64bit archs
by using unsigned long.
- Shadow this arithmetic overflow workaround by introducing
helper functions: addrconf_timeout_fixup() and
addrconf_finite_timeout().
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
As of now, the prefix length is not vaildated when adding or deleting
addresses. The value is passed directly into the inet6_ifaddr structure
and later passed on to memcmp() as length indicator which relies on
the value never to exceed 128 (bits).
Due to the missing check, the currently code allows for any 8 bit
value to be passed on as prefix length while using the netlink
interface, and any 32 bit value while using the ioctl interface.
[Use unsigned int instead to generate better code - yoshfuji]
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
We need to handle infinite prefix lifetime specially.
With help from original reporter "Bonitch, Joseph"
<Joseph.Bonitch@xerox.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Noticed from Al Viro <viro@ftp.linux.org.uk> via David Miller
<davem@davemloft.net>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netns start-stop engine can happily live with any of
init or exit callbacks set to NULL.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As far as I can remember, I was going to disable privacy extensions
on all "tunnel" interfaces. Disable it on ip6-ip6 interface as well.
Also, just remove ifdefs for SIT for simplicity.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since NETDEV_REGISTER notifier chain is responsible for creating
inet6_dev{}, we do not need to call ipv6_find_idev() directly here.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have been using __NET_IPV6_MAX for adjusting the size of array
for sysctl table, but it does not work any longer because of the
deprecation of NET_IPV6_xxx constants. Let's use DEVCONF_MAX
instead.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
In the other case it will be destroyed when last address will be removed
from lo inside a namespace. This will break IPv6 in several places. The
most obvious one is ip6_dst_ifdown.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
addrconf_ifdown is broken in respect to the usage of how
parameter. This function is called with (event != NETDEV_DOWN) and (2)
on the IPv6 stop. It the latter case inet6_dev from loopback device
should be destroyed.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From RFC341:
A temporary address is created only if this calculated Preferred
Lifetime is greater than REGEN_ADVANCE time units. In particular, an
implementation must not create a temporary address with a zero
Preferred Lifetime.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a prefix information from a routeur, only update the
lifetimes of the temporary address associated with that prefix.
Otherwise if one deprecated prefix is advertized, all your temporary
addresses will become deprecated.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an inline net_eq() to compare two namespaces.
Without CONFIG_NET_NS, since no namespace other than &init_net
exists, it is always 1.
We do not need to convert 1) inline vs inline and
2) inline vs &init_net comparisons.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Without CONFIG_NET_NS, no namespace other than &init_net exists,
no need to store net in seq_net_private.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Introduce per-sock inlines: sock_net(), sock_net_set()
and per-inet_timewait_sock inlines: twsk_net(), twsk_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Introduce per-net_device inlines: dev_net(), dev_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the infrastructure to propagate the network namespace information
is ready. Make use of it.
There is a special case here between the initial network namespace and
the other namespaces:
* When ipv6 is initialized at boot time (aka in the init_net), it
registers to the notifier callback. So addrconf_notify will be called
as many time as there are network devices setup on the system and the
function will add ipv6 addresses to the network devices. But the first
device which needs to have its ipv6 address setup is the loopback,
unfortunatly this is not the case. So the loopback address is setup
manually in the ipv6 init function.
* With the network namespace, this ordering problem does not appears
because notifier is already setup and active, so as soon as we
register the loopback the ipv6 address is setup and it will be the
first device.
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch propagates the network namespace pointer to the address
configuration routines which need it, which means adding a new
parameter to these functions, and make them use it instead of using
the initial network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rt6_info structures are moved inside the network namespace
structure. All references to these structures are now relative to the
initial network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch make mindless changes and prepares the code to use dynamic
allocation for rt6_info structure. The code accesses the rt6_info
structure as a pointer instead of a global static variable.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a network namespace parameter to rt6_purge_dflt_routers. This is
needed to call fib6_get_table with the appropriate network namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stephen Hemminger