Channel switch host command do not need to allocate huge command buffer
since its size is already included in the iwl_device_cmd structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Support channel switch in driver as a separated mac80211 callback
function instead of part of mac_config callback; by moving to this
approach, uCode can have more control of channel switch timing.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move the ucode beacon formation related helper function from 3945 to
iwlcore, so both _3945 and _agn devices can utilize those functions.
When driver pass the beacon related timing information to uCode in both
spectrum measurement and channel switch commands, the beacon timing
parameter require in uCode beacon format; those helper functions will do
the conversation from uSec to the correct uCode format
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add new PCI IDs for 6000 Series Gen2 devices
and also defines a new sku of device: 6000g2b 2x2 bgn.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This patch enables all remaining 6000 series Gen2 devices.
To work-around a firmware crash problem, we disable sending
bt coex command for 6000g2b series devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently, the broadcast station is managed along
with the interface type, rather than always being
present. That leads to a bug with injection -- it
is currently not possible to inject frames when
the only virtual interface is a monitor, because
in that the required broadcast station is missing.
Additionally, allocating and deallocating the
broadcast station's LQ all the time is wasteful,
and the code to support this is fairly complex.
So this changes completely the way we manage the
broadcast station. Rather than manage it along
with any interface, we now allocate it when we
bring the device up, and remove it again when we
bring the device down. When we bring the device
up, we don't immediately program the broadcast
station into it, instead we just mark it active
and rely on the next restore cycle to upload it
to the device. This works because an unassociated
RXON is always required at least once to set up
device parameters, which implies a reprogramming
of stations into the device.
As we now manage all stations properly, there no
longer is a need for forcing a clearing of them
via iwl_clear_ucode_stations(), which can become
a lot simpler.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
AGN devices all use the same ucode operations,
except for 4965, because 4965 uses only v1 file
headers.
Therefore, we can remove all the indirection
we have here and just code the API distinction
in place, with a small special case for 4965.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Currently iwlwifi will eventually exhaust the station
table when adding the BSSID station for IBSS mode,
unless the interface is set down.
The new mac80211 ibss joined/left notification allows
us to fix that easily by moving the code to add the
IBSS station to the notification, and also adding
code to remove it again when we leave the IBSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
sensitivity calibration and chain noise calibration are not available
for all the devices; use .cfg to configure the availability of those
calibration functions
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Instead of checking device type for enable/disable continuous ucode
trace function; put it in .cfg for better control and more
flexibilities.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Rename the current 6000 series Gen2 devices to Gen2a.
Rename the ucode name prefix to iwlwifi-6000g2a.
Also corrected the device IDs for Gen2a series devices.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Greenfield is a 11n feature, remove it from non-11n devices
configuration parameters list
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Separate the hw_set_hw_params() function to per device based; different
devices can have different hardware parameters set, when separate the
function based on device type can avoid mistakes, give more flexibilities and
easier to read.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For 6000g2 series of NICs, PA type is determined by uCode, driver do not
have to set the register for internal/external PA. It is a workaround
just for 6000 series NICs.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This patch is to bring up 6000 Series 2x2 AGN Gen2 adapters.
Seperate various version numbers from 6000 Series definitions;
Add module firmware declaration for the new adapters;
Add additional device IDs and subsystem IDs;
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For 6000 series, the 2.4G HT40 band regulatory settings address in EEPROM
was off by 2.
Before the fix, you'll see this in dmesg:
[79535.788877] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
[79535.788880] ieee80211 phy8: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
WIDE (0x61 0dBm): Ad-Hoc not supported
And after the fix:
[91132.688706] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 7 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
[91132.688709] ieee80211 phy14: U iwl_mod_ht40_chan_info HT40 Ch. 11 [2.4GHz]
IBSS ACTIVE WIDE (0x6f 0dBm): Ad-Hoc supported
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Size of event log is determined by uCode which is different per NICs.
Set the maximum event log size per device to better match uCode
configuration.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
agn module parameter data structure shared by all agn devices, move it
iwl-agn-lib.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Each device has it own eeprom, so the tx power version could be
different, define TX_POWER_VERSION per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices share the same common functions.
Move those functions from iwl-5000.c to iwl-agn-lib.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
uCode alive for iwlagn based devices share the same functions.
Move those functions from iwl-5000.c to iwl-agn-ucode.c.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same hw definitions.
Move device hardware related defines from iwl-5000-hw.h to iwl-agn-hw.h
file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same tansmit queue functions.
Move tx queue related code from iwl-5000.c to iwl-agn-tx.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same hcmd related functions.
Move from iwl-5000.c to iwl-agn-hcmd.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Loading uCode functions are shared across multiple agn devices.
Move those functions to iwl-agn-ucode.c file with other uCode
related functions.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same ucode loading procedure.
Move loading related code from iwl-5000.c to iwl-agn-ucode.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Split the connectivity check and recovery routine into separated
functions based on the types
1. iwl_good_ack_health() - check for ack count
2. iwl_good_plcp_health() - check for plcp error
Based on the type of errors being detected, different recovery methods
will be used to bring the system back to normal operational state.
Because different NIC has different HW and uCode, the behavior is also
different; these functions thus now form part of the ops infrastructure,
so we can have more control on how to monitor and recover from error condition
case per device.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Move the plcp error checking into stand alone function and pointed by ops
to accommodate devices not needing this recovery.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Monitors the internal TX queues periodically. When a queue is stuck
for some unknown conditions causing the throughput to drop and the
transfer is stop, the driver will force firmware reload and bring the
system back to normal operational state.
The iwlwifi devices behave differently in this regard so this feature is
made part of the ops infrastructure so we can have more control on how to
monitor and recover from tx queue stall case per device.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Align the driver names with official product names for 1000/5000/6000
series. This change mainly affects the debug messages show up in system
log. No functional changes.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
All the ICT ISR code is iwlagn specific, and doesn't
need to be in iwlcore. So create a new iwl-agn.h
header file that will hold agn specific function
declarations etc., and move the ICT code into a new
iwl-agn-ict.c file that is linked into iwlagn. This
also gets rid of exporting those symbols.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Indicate calibration version to uCode
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing iwl6050_ops->iwl6050_hcmd_utils structure had no pointers to chain
noise functions (gain_computation and chain_noise_reset). As it turns out,
by adding chain_noise_scale (see related patch), there is no need for separate
chain noise function, so simply use iwl6000_ops->iwl5000_hcmd_utils, and
remove those for 6050.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
6x50 device requires a different scaling factor for Rx gain values sent to
device via PHY_CALIBRATION_CMD (CHAIN_NOISE_GAIN_CMD). Rather than create
a new iwlXXXX_gain_computation() function, add new chain_noise_scale member
to struct iwl_cfg, and keep using iwl5000_gain_computation().
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update sensitivity range values for 6000 & 6x50 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Add function pointer for broadcast station addition so that we can call it
in from iwlcore at a later time. We only distinguish between iwlagn and
iwl3945 broadcast station addition. For the iwl3945 station addition we add
that function to iwlcore since that is where most station functionality
resides, making it part of iwl3945 will require significant code
reorganization that will dilute station management functionality. This
seems to be an efficient solution.
It may seem as though we are removing error checking when adding the 3945
broadcast station but this error checking was never really necessary since
the function returns the station id and the broadcast station id is always
set.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
For 6X50 DC calibration needs to be initialized
else uCode will run an endless loop.
Enbale DC calibration in hw config.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have seen the throughput dropped due to external noisy environment
and the radio is out of tune. There are lot of plcp errors indicating
this condition. Eventually the station can get de-authenticated by the
Access Point. By resetting and tuning the radio, the plcp errors are
reduced or eliminated and the throughput starts to rise.
To prevent unexpected behavior such as drop in throughput or deauthentication,
- The change provides the driver feature to monitor and tune the radio base on
the statistics notification from the uCode.
- It also allows the setting of the plcp error rate threshold via
the plcp_delta under debugfs interface.
Signed-off-by: Trieu 'Andrew' Nguyen <trieux.t.nguyen@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Flowhandler handle the communication between driver and uCode, when any
uCode error happen, we also like to know what is the status of the
flowhandler; it can help to debug flowhandler related problem.
Also adding debugfs file to dump current value of flowhandler registers.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hard-coding the SM PS mode per hardware,
this makes iwlwifi support the new mac80211 API for
controlling the SM PS mode.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When uCode HW/SW error detected, dumping important CSR (Control and Status
Registers) values.
Also add "csr" debugfs file to dump the current values of CSR defined in
CSR table to syslog.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting "Spatial multiplexing Power Save" as part of
per device configuration parameter.
Report to uCode based on priv->conf setting, so driver can
have more control of how different devices should operate
in power save mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drop the non-production PCI-IDs for 6x50 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Temporary disable the coex function for wifi/wimax for 6x50
series until the full implementation ready.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the support for all the PCI_IDs never make into production
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Different channel has different configuration, need to pass correct
configuration to uCode when send "channel switch" command to uCode.
Invalid configuration will cause sysassert in uCode and produce
un-expected result.
Even it is a very small windows, but we also need to consider and handle
the case if commit_rxon occurred before the "channel switch
announcement" notification received from uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy