arch/arm/mach-at91/board-sam9m10g45ek.c: mach/hardware.h is included more than once
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Final version of the patch that adds support for RS485 communications to the atmel_serial driver.
The patch has been already sent and discussed on both linux-kernel and linux-arm-kernel mailing lists several times.
Many people collaborated to improve and test the code:
Tested-by: Sebastian Heutling <Sebastian.Heutling@who-ing.de>
Tested-by: Bernhard Roth <br@pwrnet.de>
Reviewed-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Rick Bronson <rick@efn.org>
Signed-off-by: Sebastian Heutling <Sebastian.Heutling@who-ing.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Disable the processor clock when the CPU is idle.
This saves much more power than merely entering 'Wait for Interrupt' mode.
Since JTAG-debugging doesn't work when the processor clock is switched off,
make it conditional on CONFIG_DEBUG_KERNEL.
Signed-off-by: Anders Larsen <al@alarsen.net>
Acked-by: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A bit in the at91sam9g10 identification number changed between Engineering
Sample and final product. This patch will identify both as being at91sam9g10.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both boards share the same board file, as the PortuxG20 is basically an
SBC based on the Stamp9G20.
Signed-off-by: Christian Glindkamp <christian.glindkamp@taskit.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cosmetic change to mach-at91 Makefile: remove two blanks introduced
by earlier patches.
Signed-off-by: Ernst Schwab <eschwab@online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Julien Langer <julien.langer@gmail.com>
AT91: when turning off the PLLs during suspend, don't wait for the lock
flag to be set. Previously the code would always run into the loop
limitation of 1000 iterations because the flag is never set when turning
the PLLs off.
Comments from Anders Larsen:
(in http://marc.info/?l=linux-kernel&m=127058929724193&w=2)
Signed-off-by: Julien Langer <julien.langer@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
at91 slow-clock resume: Don't wait for a disabled PLL to lock.
We run into this problem with the PLLB on the at91: ohci-at91 disables
the PLLB when going to suspend. The slowclock code however tries to do
the same: It saves the PLLB register value and when restoring the value
during resume, it waits for the PLLB to lock again. However the PLL will
never lock and the loop would run into its timeout because the slowclock
code just stored and restored an empty register.
This fixes the problem by only restoring PLLA/PLLB when they were enabled
at suspend time.
Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert arm to use GENERIC_TIME via the arch_getoffset() infrastructure,
reducing the amount of arch specific code we need to maintain.
The arm architecture is the last arch that need to be converted.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
The change introduced in patch 5596/1 used incorrect bracing which
resulted in the AT24 EEPROM no longer being registered. This patch
corrects the bracing and allows both the WM8731 audio device and AT24
EEPROM device to be registered.
Signed-off-by: Rob Alley <rob.alley@navmanwireless.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some misspelled occurences of 'octet' and some comments were also fixed
as I was on it.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
on AT91 the timer irq is shared, so the handler might be entered without
irqs being disabled. Though this should not happen as the timer irq is
registered early, there have been some reports on the mailing list.
To make debugging that problem easier next time it pops up a
WARN_ON_ONCE is added to the handler if irqs are not off.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Add support for the Atmel AT572D940HF-EK board (development board for
the AT572D940HF processor).
Signed-off-by: Antonio R. Costa <costa.antonior@gmail.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the Atmel AT572D940HF processor (DIOPSIS range).
This processor integrates an ARM926 core, a DSP and the SoC
peripherals usually found on an AT91 processor (USART, SSC, SPI, TWI,
CAN, etc)
Signed-off-by: Antonio R. Costa <costa.antonior@gmail.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the use of another DMA controller driver in atmel-mci sd/mmc driver.
This adds a generic dma_slave pointer to the mci platform structure where
we can store DMA controller information. In atmel-mci we use information
provided by this structure to initialize the driver (with new helper
functions that are architecture dependant).
This also adds at32/avr32 chip modifications to cope with this new access
method.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New at91sam9g45ekes board provides a LCD with resistive touchscreen.
This is the support of this feature by atmel_tsadcc driver. This also
sets up platform parameters to be passed to the driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Setup platform parameters in at91sam9rl-ek board to be passed to
atmel_tsadcc touchscreen.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.
Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Many Atmel SOC are embedding a LCD controller. This patch removes the long
dependency line for this Atmel LCD framebuffer driver configuration entry.
The HAVE_FB_ATMEL configuration option is located in the video Kconfig file
as it may be setup by ARM/AT91 and AVR32 chips.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Instead of adding "depends on" at config level, introduce HAVE_* config
variables. Add them at machine or soc level to specify the ability of a
particular support.
It will ease new board introduction and readability.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Those "depends on" are a double check as all machine entries are
surrounded by "if <ARCH_xxx>" conditions.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
at91sam9g20ek rev. C and onwards embed two SD/MMC slots. This patch modify the
previous dual slot board definition to match the official rev. C board. It also
allows the use of at91_mci SD/MMC driver in addition to the atmel-mci one.
Some pins have been re-affected from leds or Ethernet phy IRQ to the SD/MMC
slot A. This lead to a modification of those definitions.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
CONFIG_MACH_ECO920 is enabled in at91rm9200dk_defconfig. The name is
wrong, but this is better than adding another defconfig or don't get
compile coverage at all.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the support for cpuidle on AT91 SoCs, taken from the
cpuidle support in mach-kirkwood.
cpuidle needs sdram_selfrefresh_enable and _disable, so move their
definition to a separate header file instead of duplicating the code
already used in pm.c.
Tested-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
cpu_is_xxx() macros are identifying generic at91sam9g45 chip. This patch adds
the capacity to differentiate Engineering Samples and final lots through the
inclusion of at91_cpu_fully_identify() and the related chip IDs with chip
version field preserved.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
This is the at91 specific part of USB host integration. The EHCI high speed
controller has a companion OHCI controller to manage USB full and low speed.
They are sharing the same IRQ line and vbus pin.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The macro for the watchdog has been changed from CONFIG_AT91SAM9_WATCHDOG
to CONFIG_AT91SAM9X_WATCHDOG due to AT91CAP9 chips support
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Created a modified version of the at91sam9g20 evaluation kit platform
(board-sam9g20ek-2slot-mmc.c) and device support to make use of the
updated atmel-mci driver.
As the use of two slots modify GPIO pin allocation, we create another
board file.
This requires getting the most updated arch/arm/tools/mach-types from
http://www.arm.linux.org.uk/developer/machines/download.php to have the machine
type for the at91sam9g20ek-2slot-mmc board.
[nicolas.ferre@atmel.com: printk, slot_count modification in at91sam9260_devices.c file]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Rob Emanuele <rob@emanuele.us>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch activates the at91 CAN controller for the at91sam9263ek
development board.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the device definition for the at91_can device to
the generic device definiton file for the at91sam9263.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix AC97 build breakage with converting to the shared AT91/AVR32 AC97 driver:
struct atmel_ac97_data -> struct ac97c_platform_data
CONFIG_SND_AT91_AC97 -> CONFIG_SND_ATMEL_AC97C
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the support of AC97 on the at91sam9rl chip and -ek board.
It will share the code with AVR32 ac97c alsa driver "atmel_ac97c".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the support of AC97 on the at91sam9g45 chip series and -ek board.
It will share the code with AVR32 ac97c alsa driver "atmel_ac97c".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is the integration of DMA engine driver into at91sam9g45 series
device file.
The associated driver is at_hdmac.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is the integration of DMA engine driver into at91sam9rl device file. The
associated driver is at_hdmac.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
DBGU means Debug Unit, was refered as "DGBU" in some files. Fixed to "DBGU".
Signed-off-by: Samuel R. C. Vale <srcvale@holoscopio.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Board code was wrongly setting up the reset pin for AC97 on at91sam9263ek.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch modifies the support of AC97 on the at91sam9263 ek board, so it would
share the code with AVR32.
Plus it removes a typo in at91sam9263_devices.c.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds board-specific data for IDE support on afeb9260.
Depends on #5631/1
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds platform data for CF/IDE support
and SMC init code for AT91SAM9260 SoC.
Tested-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPUAT91 is based on Atmel's AT91RM9200 with up to 16MB Strataflash,
up to 128MB SDRAM and an ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <ebenard@eukrea.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPU9260 and CPU9G20 share the same PCB populated with either
Atmel's AT91SAM9260B or AT91SAM9G20B with up to 64MB Strataflash,
up to 128MB SDRAM, up to 2GB NAND and an ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It adds DMA peripheral identifiers for hardware handshaking interface. It will
be used in platform code.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch for at_hdmac adds the slave transfers capability to the Atmel DMA
controller available on some AT91 SOCs. This allow peripheral to memory and
memory to peripheral transfers with hardware handshaking.
Slave structure for controller specific information is passed through channel
private data. This at_dma_slave structure is defined in at_hdmac.h header file
and relative hardware definition are moved to this file from at_hdmac_regs.h.
Doing this we allow the channel configuration from platform definition code.
This work is intensively based on dw_dmac and several slave implementations.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This AHB DMA Controller (aka HDMA or DMAC on AT91 systems) is availlable on
at91sam9rl chip. It will be used on other products in the future.
This first release covers only the memory-to-memory tranfer type. This is the
only tranfer type supported by this chip. On other products, it will be used
also for peripheral DMA transfer (slave API support to come).
I used dmatest client without problem in different configurations to test it.
Full documentation for this controller can be found in the SAM9RL datasheet:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4243
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The WM8731 driver has been updated to allow registration via normal
device model methods rather than from within the ASoC driver probe
so update the AT91SAM9G20-EK to make use of this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
Here are the modification to at91sam9261 files dedicated to the support of
at91sam9g10. This direction has been adopted to minimize code duplication.
All at91sam9261 drivers are enabled in _devices and board- files. Modificaton
to peripherals that support at91sam9g10 will be added in future patches.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Hong Xu <hong.xu@atmel.com>
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Here is the basic header file support for this product.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Andrea Gelmini