Hi,
This patch contains additional statistics counters added to s2io driver
these statistics are very much usefull in debugging the driver.
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
hi,
This patch contains all the changes that were done to improve
performance of s2io driver. one line description of the changes
are
1. For Non NAPI case the rx interrupt handler is being called
unconditionally
2. code optimization and adding prefetch skb->data
3. Remove modulo operations in fast path
4. Enable Group Reads and set backoff interval to 0x1000
5. correct PIC_CNTL_SHARED_SPLITS macro definition, and reduce
pause parameter
6. Corrected logic of identifying rx buffer level in rx_buffer_level()
7. fix DMA map and unmap done with different sizes in 1-buf mode
8. Removed forcible disabling of ERO
9. Send up the packets with transfer code = 0x5
Signed-off-by: Ananda Raju <ananda.raju@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following bugs with offline diagnostics
code(run with "ethtool -t").
1. After running offline diagnostics, adapter would report
corrupted packets on receive. This was because of adapter not
being brought out of "RLDRAM test mode".
2. Current EEPROM test works only for Xframe I. Since Xframe II
uses different interface(SPI), support for this interface has
been added. Also, since SPI supports write access to all areas
of EEPROM, negative testing is done only for Xframe I.
3. Return values from subfunctions of offline diagnostics have
been corrected.
4. In register test, expected value from rx_queue_cfg register
is made to depend on adapter type.
5. After the test, need to restore values at EEPROM offsets
0x4F0 and 0x7F0. These locations were modified as part of test.
6. Use macro SPECIAL_REG_WRITE for write access to mc_rldram_test_ctrl
register. Also, couple of unnecessary writes to mc_rldram_test_ctrl
have been removed.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch contains the following hardware related fixes and other
miscellaneous bug fixes.
1. Updated the definition of single and double-bit ECC errors
2. Earlier we were allocating Transmit descriptors equal to
MAX_SKB_FRAGS. This was causing a boundary condition failure.
Need to allocate MAX_SKB_FRAGS+1 descriptors.
3. On some platforms(like PPC), pci_alloc_consistent() can return
a zero DMA address. Since the NIC cannot handle zero-addresses,
a workaround has been provided. Basically, we don't use such
that page. We reallocate.
4. If list_info allocation failed during driver load, check for
it during driver exit and return instead of trying to dereference
NULL pointer.
5. Increase the debug level of few non-critical debug messages.
6. Reset the card on critical ECC double errors only in case of
XframeI since XframeII can recover from such errors.
7. Print copyright message on driver load.
8. Bumped up the driver version no. to 2.0.8.1
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
The below patch implements a new "Link state change handling"
scheme supported by the Xframe II adapter. It also bumps up the
driver version to 2.0.2.0.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
This patch provides basic support for the Xframe II adapter.
Includes the following changes:
1. New values to program XAUI interface.
2. Print the PCI/PCI-X mode(bus frequency, width).
3. Remove EOI from reset during intialization.
4. Enable all 8 PCCs if Xframe II adapter.
5. Programs the RLDRAM size depending on the device.
(Note: RLDRAM size on XFARME-I is 64Mb whereas on XFRAME-II it's 32 Mb).
6. Enable extended(64-bit) statistics counters.
7. Program timer interrupt duration based on PCI/PCI-X clock speed.
8. Not required to save/restore PCI config space before/after reset.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
Below patch addresses few h/w specific issues.
1. Check for additional ownership bit on Rx path before
starting Rx processing.
2. Enable only 4 PCCs(Per Context Controller) for Xframe I
revisions less than 4.
3. Program Rx and Tx round robin registers depending on
no. of rings/FIFOs.
4. Tx continous interrupts is now a loadable parameter.
5. Reset the card if we get double-bit ECC errors.
6. A soft reset of XGXS being done to force a link state change has been
eliminated.
7. After a reset, clear "parity error detected" bit,
PCI-X ECC status register, and PCI_STATUS bit in
tx_pic_int register.
8. The error in the disabling allmulticast implementation has been
rectified.
9. Leave the PCI-X parameters MMRBC, OST etc. at their
BIOS/system defaults.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
We are submitting a series of 13 patches to support our Xframe I and
Xframe II line of products. The patches can be categorized as follows:
Patches 1-8 : Changes applicable to both Xframe I and II
Patches 9-11: Xframe II specific features
Patch 12: Addresses issues found during testing cycle.
Patch 13: Incorpoates mostly the review comments from community
and some last moment bug fixes.
Please review the patches and let us know your comments.
Starting with patch 1 below.
This patch involves cosmetic changes(tabs and indentation,
regrouping of transmit and receive data structures, typecasting,
code cleanup).
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Jeff Garzik