ARM: dts: msm: Add display support sm6150 based trinket interposer

This change adds display support for sm6150 based trinket
interposer.

Change-Id: Ifb1e401a0b69e10958650285e0e9c70badea11c1
Signed-off-by: Vishnuvardhan Prodduturi <vproddut@codeaurora.org>

arch/arm64/boot/dts/qcom/sm6150-interposer-trinket-idp-overlay.dts

@@ -23,3 +23,7 @@
 	qcom,msm-id = <355 0x0>;
 	qcom,board-id = <34 0>;
 };
+
+&dsi_td4330_truly_vid_display {
+	qcom,dsi-display-active;
+};

arch/arm64/boot/dts/qcom/sm6150-interposer-trinket-idp.dtsi

@@ -13,6 +13,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include "sm6150-sde-display.dtsi"
 
 &pm6125_gpios {
 	key_vol_up {
@@ -45,3 +46,45 @@
 		};
 	};
 };
+
+&sde_dp {
+	/delete-property/ qcom,dp-usbpd-detection;
+	status = "disabled";
+};
+
+&mdss_dsi0 {
+	vdda-1p2-supply = <&L18A>;
+};
+
+&mdss_dsi_phy0 {
+	vdda-0p9-supply = <&L4A>;
+};
+
+&sde_dsi {
+	vddio-supply = <&L9A>;
+};
+
+&mdss_mdp {
+	connectors = <&sde_rscc &sde_wb &sde_dsi>;
+};
+
+&dsi_td4330_truly_video {
+	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
+	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
+	qcom,mdss-dsi-bl-min-level = <1>;
+	qcom,mdss-dsi-bl-max-level = <4095>;
+	qcom,platform-reset-gpio = <&tlmm 91 0>;
+	qcom,platform-en-gpio = <&pm6125_gpios 8 0>;
+	qcom,platform-bklight-en-gpio = <&pmi632_gpios 6 0>;
+};
+
+&dsi_td4330_truly_cmd {
+	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
+	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
+	qcom,mdss-dsi-bl-min-level = <1>;
+	qcom,mdss-dsi-bl-max-level = <4095>;
+	qcom,platform-te-gpio = <&tlmm 90 0>;
+	qcom,platform-reset-gpio = <&tlmm 91 0>;
+	qcom,platform-en-gpio = <&pm6125_gpios 8 0>;
+	qcom,platform-bklight-en-gpio = <&pmi632_gpios 6 0>;
+};

arch/arm64/boot/dts/qcom/sm6150-sde-display.dtsi

@@ -17,6 +17,8 @@
 #include "dsi-panel-td4328-1080p-cmd.dtsi"
 #include "dsi-panel-rm69298-truly-amoled-fhd-plus-video.dtsi"
 #include "dsi-panel-rm69298-truly-amoled-fhd-plus-cmd.dtsi"
+#include "dsi-panel-td4330-truly-singlemipi-fhd-cmd.dtsi"
+#include "dsi-panel-td4330-truly-singlemipi-fhd-video.dtsi"
 #include <dt-bindings/clock/mdss-14nm-pll-clk.h>
 
 &soc {
@@ -170,6 +172,28 @@
 		qcom,dsi-panel = <&dsi_rm69298_truly_amoled_cmd>;
 	};
 
+	dsi_td4330_truly_vid_display: qcom,dsi-display@7 {
+		label = "dsi_td4330_truly_vid_display";
+		qcom,display-type = "primary";
+
+		qcom,dsi-ctrl-num = <0>;
+		qcom,dsi-phy-num = <0>;
+		qcom,dsi-select-clocks = "src_byte_clk0", "src_pixel_clk0";
+
+		qcom,dsi-panel = <&dsi_td4330_truly_video>;
+	};
+
+	dsi_td4330_truly_cmd_display: qcom,dsi-display@8 {
+		label = "dsi_td4330_truly_cmd_display";
+		qcom,display-type = "primary";
+
+		qcom,dsi-ctrl-num = <0>;
+		qcom,dsi-phy-num = <0>;
+		qcom,dsi-select-clocks = "src_byte_clk0", "src_pixel_clk0";
+
+		qcom,dsi-panel = <&dsi_td4330_truly_cmd>;
+	};
+
 	sde_dsi: qcom,dsi-display {
 		compatible = "qcom,dsi-display";
 
@@ -197,7 +221,9 @@
 			&dsi_td4328_truly_vid_display
 			&dsi_td4328_truly_cmd_display
 			&dsi_rm69298_truly_amoled_vid_display
-			&dsi_rm69298_truly_amoled_cmd_display>;
+			&dsi_rm69298_truly_amoled_cmd_display
+			&dsi_td4330_truly_vid_display
+			&dsi_td4330_truly_cmd_display>;
 	};
 
 	sde_wb: qcom,wb-display@0 {
@@ -402,3 +428,39 @@
 		};
 	};
 };
+
+&dsi_td4330_truly_cmd {
+	qcom,mdss-dsi-t-clk-post = <0x0e>;
+	qcom,mdss-dsi-t-clk-pre = <0x36>;
+	qcom,mdss-dsi-display-timings {
+		timing@0{
+			qcom,mdss-dsi-panel-phy-timings =
+				[26 20 09 0B 06 02 04 a0
+				26 20 09 0B 06 02 04 a0
+				26 20 09 0B 06 02 04 a0
+				26 20 09 0B 06 02 04 a0
+				26 1F 09 0B 06 02 04 a0];
+
+			qcom,display-topology = <1 0 1>;
+			qcom,default-topology-index = <0>;
+		};
+	};
+};
+
+&dsi_td4330_truly_video {
+	qcom,mdss-dsi-t-clk-post = <0x0e>;
+	qcom,mdss-dsi-t-clk-pre = <0x36>;
+	qcom,mdss-dsi-display-timings {
+		timing@0{
+			qcom,mdss-dsi-panel-phy-timings =
+				[26 20 09 0B 06 02 04 a0
+				26 20 09 0B 06 02 04 a0
+				26 20 09 0B 06 02 04 a0
+				26 20 09 0B 06 02 04 a0
+				26 1F 09 0B 06 02 04 a0];
+
+			qcom,display-topology = <1 0 1>;
+			qcom,default-topology-index = <0>;
+		};
+	};
+};