# This file allows user to override the factory # defaults for the WLAN Driver # Enable IMPS or not gEnableImps=1 # Enable BMPS or not gEnableBmps=1 # Phy Mode (auto, b, g, n, etc) # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only # 7 = 11b only 8 = 11ac only. gDot11Mode=0 # Assigned MAC Addresses - This will be used until NV items are in place # Each byte of MAC address is represented in Hex format as XX Intf0MacAddress=000AF58989FF Intf1MacAddress=000AF58989FE Intf2MacAddress=000AF58989FD Intf3MacAddress=000AF58989FC # UAPSD service interval for VO,VI, BE, BK traffic InfraUapsdVoSrvIntv=0 InfraUapsdViSrvIntv=0 InfraUapsdBeSrvIntv=0 InfraUapsdBkSrvIntv=0 # Flag to allow STA send AddTspec even when ACM is Off gAddTSWhenACMIsOff=1 # Flags to filter Mcast and Bcast RX packets. # Value 0: No filtering, 1: Filter all Multicast. # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast McastBcastFilter=3 #Flag to enable HostARPOffload feature or not hostArpOffload=1 #Flag to enable HostNSOffload feature or not hostNSOffload=1 # 802.11n Protection flag gEnableApProt=1 #Enable OBSS protection gEnableApOBSSProt=1 #Enable/Disable UAPSD for SoftAP gEnableApUapsd=1 # Fixed Rate gFixedRate=0 # Maximum Tx power # gTxPowerCap=30 # Fragmentation Threshold # gFragmentationThreshold=2346 # RTS threshold RTSThreshold=1048576 # Intra-BSS forward gDisableIntraBssFwd=0 # WMM Enable/Disable WmmIsEnabled=0 # 802.11d support g11dSupportEnabled=0 # 802.11h support g11hSupportEnabled=1 # DFS Master Capability gEnableDFSMasterCap=1 # ESE Support and fast transition EseEnabled=0 ImplicitQosIsEnabled=0 gNeighborScanTimerPeriod=200 gNeighborLookupThreshold=76 gNeighborScanChannelMinTime=20 gNeighborScanChannelMaxTime=30 gMaxNeighborReqTries=3 # Legacy (non-ESE, non-802.11r) Fast Roaming Support # To enable, set FastRoamEnabled=1 # To disable, set FastRoamEnabled=0 FastRoamEnabled=1 # Check if the AP to which we are roaming is better than current AP in # terms of RSSI. Checking is disabled if set to Zero.Otherwise it will # use this value as to how better the RSSI of the new/roamable AP should # be for roaming RoamRssiDiff=5 # To enable, set gRoamIntraBand=1 (Roaming within band) # To disable, set gRoamIntraBand=0 (Roaming across band) gRoamIntraBand=0 #Short Guard Interval Enable/disable gShortGI20Mhz=1 gShortGI40Mhz=1 #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled gAPAutoShutOff=0 #Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec gWlanAutoShutdown = 0 # Not used. gApAutoChannelSelection=0 #Preferred band (both or 2.4 only or 5 only) BandCapability=0 #Channel Bonding gChannelBondingMode5GHz=1 #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link #is idle for last 10 seconds.) For both active and power save clients. #Power save clients: DUT set TIM bit from 10th second onwards and till client #honors TIM bit. If doesn't honor for 5 seconds then DUT remove client. #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not #success still we try on 11th second if not tries on 12th and so on till 15th #second. Hence before disconnection DUT will send 5 NULL frames. Hence in any #case DUT will detect client got removed in (10+5) seconds. #i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and #it is period where we send NULL frame. #gApLinkMonitorPeriod = 10 #gGoLinkMonitorPeriod = 10 #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame #are succeed to send or not. Hence total effective detection time is # (gGoLinkMonitorPeriod + gGoKeepAlivePeriod) / # (gApLinkMonitorPeriod + gApKeepAlivePeriod) gGoKeepAlivePeriod = 20 gApKeepAlivePeriod = 20 #If set will start with active scan after driver load, otherwise will start with #passive scan to find out the domain gEnableBypass11d=1 #If set to 0, will not scan DFS channels gEnableDFSChnlScan=1 # Enable DFS channel roam # 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE gAllowDFSChannelRoam=1 gVhtChannelWidth=2 #Data Inactivity Timeout when in powersave (in ms) gDataInactivityTimeout=200 # Set txchainmask and rxchainmask # These parameters are used only if gEnable2x2 is 0 # Valid values are 1,2 # Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. # Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. gSetTxChainmask1x1=1 gSetRxChainmask1x1=1 # Scan Timing Parameters # gPassiveMaxChannelTime=110 # gPassiveMinChannelTime=60 gActiveMaxChannelTime=40 gActiveMinChannelTime=20 #If set to 0, MCC is not allowed. gEnableMCCMode=1 # MCC to SCC Switch mode: # 0-Disable # 1-Enable # 2-Force SCC if same band, with SAP restart # 3-Force SCC if same band, without SAP restart by sending (E)CSA # 4-Force SCC if same band (or) use SAP mandatory channel for DBS, # without SAP restart by sending (E)CSA gWlanMccToSccSwitchMode = 3 # 1=enable STBC; 0=disable STBC gEnableRXSTBC=1 # 1=enable tx STBC; 0=disable gEnableTXSTBC=1 # 1=enable rx LDPC; 0=disable gEnableRXLDPC=1 #Enable/Disable Tx beamforming gTxBFEnable=1 #Enable/Disable Tx beamformee in SAP mode gEnableTxBFeeSAP=1 # Enable Tx beamforming in VHT20MHz # Valid values are 0,1. If commented out, the default value is 0. # 0=disable, 1=enable gEnableTxBFin20MHz=1 #Enable/Disable SU Tx beamformer support. gEnableTxSUBeamformer=1 gEnableFastRoamInConcurrency=1 #Maxium Channel time in msec gMaxMediumTime = 6000 # 802.11K support gRrmEnable=1 #Enable Power Save offload gEnablePowerSaveOffload=2 #Enable firmware uart print gEnablefwprint=0 # Firmware log mode # Valid values are 0,1,2 # 0=Disable, 1=WMI, 2=DIAG gEnablefwlog=1 # Maximum Receive AMPDU size (VHT only. Valid values: # 0->8k 1->16k 2->32k 3->64k 4->128k) gVhtAmpduLenExponent=7 # Maximum MPDU length (VHT only. Valid values: # 0->3895 octets, 1->7991 octets, 2->11454 octets) gVhtMpduLen=2 # Maximum number of wow filters required #gMaxWoWFilters=22 # WOW Enable/Disable. # 0 - Disable both magic pattern match and pattern byte match. # 1 - Enable magic pattern match on all interfaces. # 2 - Enable pattern byte match on all interfaces. # 3 - Enable both magic pattern and pattern byte match on all interfaces. # Default value of gEnableWoW is 3. # gEnableWoW=0 # Enable or Disable MCC Adaptive Scheduler at the FW # 1=Enable (default), 0=Disable gEnableMCCAdaptiveScheduler=1 #Enable or Disable p2p device address administered isP2pDeviceAddrAdministrated=0 # Remove Overlap channel restriction gEnableOverLapCh=0 #Enable VHT on 2.4Ghz gEnableVhtFor24GHzBand=1 #Maximum number of offload peers supported # gMaxOffloadPeers=2 # controlling the following offload patterns # through ini parameter. Default value is 1 # to disable set it to zero. ssdp = 0 # Setup multicast pattern for mDNS 224.0.0.251, # SSDP 239.255.255.250 and LLMNR 224.0.0.252 ssdp=0 #Enable Memory Deep Sleep gEnableMemDeepSleep=1 # Regulatory Setting; 0=STRICT; 1=CUSTOM gRegulatoryChangeCountry=1 # RA filtering rate limit param, the current value would not # help if the lifetime in RA is less than 3*60=3min. Then # we need to change it, though it is uncommon. # gRAFilterEnable=0 gRArateLimitInterval=600 # Maximum number of concurrent connections gMaxConcurrentActiveSessions=3 # Disable/Enable GreenAP # 0 to disable, 1 to enable, default: 1 gEnableGreenAp=0 # Radar PRI multiplier gDFSradarMappingPriMultiplier=4 gPNOScanSupport=1 #Enable/Disable LPASS support # 0 to disable, 1 to enable gEnableLpassSupport=1 # Whether userspace country code setting shld have priority gCountryCodePriority=1 # Enable(1)/Disable(0) SIFS burst gEnableSifsBurst=1 # Enable or Disable Multi-user MIMO # 1=Enable (default), 0=Disable gEnableMuBformee=1 # Enable/Disable channel avoidance for SAP in SCC scenario # 0 - disable # 1 - enable gSapSccChanAvoidance=0 # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode gIbssTxSpEndInactivityTime=10 # Enable TDLS External Control. That is, user space application has to # first configure a peer MAC in wlan driver towards which TDLS is desired. # Device will establish TDLS only towards those configured peers whenever # TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS # when teardown criteria (idle packet count and RSSI) is met. However, # device will accept TDLS connection if it is initiated from any other peer, # even if that peer is not configured. # 0 - disable # 1 - enable # For TDLS External Control, Implicit Trigger must also be enabled. gTDLSExternalControl=1 # Enable support for TDLS off-channel operation # 0 - disable # 1 - enable # TDLS off-channel operation will be invoked when there is only one # TDLS connection. gEnableTDLSOffChannel=1 # Enable or Disable Random MAC (Spoofing) # 1=Enable (default), 0=Disable gEnableMacAddrSpoof=1 ################ Datapath feature set Begin ################ # Bus bandwidth threshold values in terms of number of packets gBusBandwidthHighThreshold=2000 gBusBandwidthMediumThreshold=500 gBusBandwidthLowThreshold=150 # Bus bandwidth compute timeout value in ms gBusBandwidthComputeInterval=100 # VHT Tx/Rx MCS values # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gVhtRxMCS=2 gVhtTxMCS=2 # VHT Tx/Rx MCS values for 2x2 # Valid values are 0,1,2. If commented out, the default value is 0. # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 gEnable2x2=1 gVhtRxMCS2x2=2 gVhtTxMCS2x2=2 #IPA config is a bit mask and following are the configurations. #bit0 IPA Enable #bit1 IPA PRE Filter enable #bit2 IPv6 enable #bit3 IPA Resource Manager (RM) enable #bit4 IPA Clock scaling enable #bit5 IPA uC ENABLE #bit6 IPA uC STA ENABLE #bit8 IPA Real Time Debugging gIPAConfig=0x7d gIPADescSize=800 # Enable/Disable RX full reorder offload gReorderOffloadSupported=1 # Enable CE classification # 1 - enable(default) 0 - disable gCEClassifyEnable=1 # Enable Rx handling options # Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium) rx_mode=5 # Enable(Tx) fastpath for data traffic. # 1 - enable(default) 0 - disable gEnableFastPath=1 # This flag enables IP, TCP and UDP checksum offload # 1 - enable(default) 0 - disable gEnableIpTcpUdpChecksumOffload=1 # Enable TCP Segmentation Offload # 1 - enable 0 - disable TSOEnable=1 # Enable Generic Receive Offload # 1 - enable(default) 0 - disable GROEnable=1 # Enable HT MPDU Density # 4 for 2 micro sec ght_mpdu_density=4 # Enable flow steering to enable multiple CEs for Rx flows. # Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs. # Parallel Rx paths. # 1 - enable 0 - disable(default) gEnableFlowSteering=1 # Time in microseconds after which a NAPI poll must yield ce_service_max_yield_time=500 #Maximum number of HTT messages to be processed per NAPI poll ce_service_max_rx_ind_flush=1 # Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND maxMSDUsPerRxInd=8 # Enable NUD tracking feature # 1 - enable 0 - disable(default) gEnableNUDTracking=1 # Enable PEER UNMAP CONF SUPPORT # 1 - enable 0 - disable(default) gEnablePeerUnmapConfSupport=1 ################ Datapath feature set End ################ ################ NAN feature set start ################### # Enable NAN discovery (NAN 1.0) # 1 - enable 0 - disable(default) gEnableNanSupport=1 # Enable NAN Datapath genable_nan_datapath=1 ################ NAN feature set end ##################### adaptive_dwell_mode_enabled=1 hostscan_adaptive_dwell_mode=1 adapt_dwell_lpf_weight=80 adapt_dwell_wifi_act_threshold=10 MAWCEnabled=0 # Enable/Disable rtt sta mac randomization enable_rtt_mac_randomization=1 #Enable/Disable SNR monitoring gEnableSNRMonitoring=1 END # Note: Configuration parser would not read anything past the END marker