You can not select more than 25 topics Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
device_samsung_sm7125-common/configs/wifi/WCNSS_qcom_cfg.ini

464 lines
12 KiB

# This file allows user to override the factory
# defaults for the WLAN Driver
# Enable IMPS or not
gEnableImps=1
# Enable BMPS or not
gEnableBmps=1
# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only
# 7 = 11b only 8 = 11ac only.
gDot11Mode=0
# Assigned MAC Addresses - This will be used until NV items are in place
# Each byte of MAC address is represented in Hex format as XX
Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD
Intf3MacAddress=000AF58989FC
# UAPSD service interval for VO,VI, BE, BK traffic
InfraUapsdVoSrvIntv=0
InfraUapsdViSrvIntv=0
InfraUapsdBeSrvIntv=0
InfraUapsdBkSrvIntv=0
# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff=1
# Flags to filter Mcast and Bcast RX packets.
# Value 0: No filtering, 1: Filter all Multicast.
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
McastBcastFilter=3
#Flag to enable HostARPOffload feature or not
hostArpOffload=1
#Flag to enable HostNSOffload feature or not
hostNSOffload=1
# 802.11n Protection flag
gEnableApProt=1
#Enable OBSS protection
gEnableApOBSSProt=1
#Enable/Disable UAPSD for SoftAP
gEnableApUapsd=1
# Fixed Rate
gFixedRate=0
# Maximum Tx power
# gTxPowerCap=30
# Fragmentation Threshold
# gFragmentationThreshold=2346
# RTS threshold
RTSThreshold=1048576
# Intra-BSS forward
gDisableIntraBssFwd=0
# WMM Enable/Disable
WmmIsEnabled=0
# 802.11d support
g11dSupportEnabled=0
# 802.11h support
g11hSupportEnabled=1
# DFS Master Capability
gEnableDFSMasterCap=1
# ESE Support and fast transition
EseEnabled=0
ImplicitQosIsEnabled=0
gNeighborScanTimerPeriod=200
gNeighborLookupThreshold=76
gNeighborScanChannelMinTime=20
gNeighborScanChannelMaxTime=30
gMaxNeighborReqTries=3
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled=1
# Check if the AP to which we are roaming is better than current AP in
# terms of RSSI. Checking is disabled if set to Zero.Otherwise it will
# use this value as to how better the RSSI of the new/roamable AP should
# be for roaming
RoamRssiDiff=5
# To enable, set gRoamIntraBand=1 (Roaming within band)
# To disable, set gRoamIntraBand=0 (Roaming across band)
gRoamIntraBand=0
#Short Guard Interval Enable/disable
gShortGI20Mhz=1
gShortGI40Mhz=1
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
gAPAutoShutOff=0
#Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec
gWlanAutoShutdown = 0
# Not used.
gApAutoChannelSelection=0
#Preferred band (both or 2.4 only or 5 only)
BandCapability=0
#Channel Bonding
gChannelBondingMode5GHz=1
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link
#is idle for last 10 seconds.) For both active and power save clients.
#Power save clients: DUT set TIM bit from 10th second onwards and till client
#honors TIM bit. If doesn't honor for 5 seconds then DUT remove client.
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not
#success still we try on 11th second if not tries on 12th and so on till 15th
#second. Hence before disconnection DUT will send 5 NULL frames. Hence in any
#case DUT will detect client got removed in (10+5) seconds.
#i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and
#it is period where we send NULL frame.
#gApLinkMonitorPeriod = 10
#gGoLinkMonitorPeriod = 10
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame
#are succeed to send or not. Hence total effective detection time is
# (gGoLinkMonitorPeriod + gGoKeepAlivePeriod) /
# (gApLinkMonitorPeriod + gApKeepAlivePeriod)
gGoKeepAlivePeriod = 20
gApKeepAlivePeriod = 20
#If set will start with active scan after driver load, otherwise will start with
#passive scan to find out the domain
gEnableBypass11d=1
#If set to 0, will not scan DFS channels
gEnableDFSChnlScan=1
# Enable DFS channel roam
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
gAllowDFSChannelRoam=1
gVhtChannelWidth=2
#Data Inactivity Timeout when in powersave (in ms)
gDataInactivityTimeout=200
# Set txchainmask and rxchainmask
# These parameters are used only if gEnable2x2 is 0
# Valid values are 1,2
# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
gSetTxChainmask1x1=1
gSetRxChainmask1x1=1
# Scan Timing Parameters
# gPassiveMaxChannelTime=110
# gPassiveMinChannelTime=60
gActiveMaxChannelTime=40
gActiveMinChannelTime=20
#If set to 0, MCC is not allowed.
gEnableMCCMode=1
# MCC to SCC Switch mode:
# 0-Disable
# 1-Enable
# 2-Force SCC if same band, with SAP restart
# 3-Force SCC if same band, without SAP restart by sending (E)CSA
# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
# without SAP restart by sending (E)CSA
gWlanMccToSccSwitchMode = 3
# 1=enable STBC; 0=disable STBC
gEnableRXSTBC=1
# 1=enable tx STBC; 0=disable
gEnableTXSTBC=1
# 1=enable rx LDPC; 0=disable
gEnableRXLDPC=1
#Enable/Disable Tx beamforming
gTxBFEnable=1
#Enable/Disable Tx beamformee in SAP mode
gEnableTxBFeeSAP=1
# Enable Tx beamforming in VHT20MHz
# Valid values are 0,1. If commented out, the default value is 0.
# 0=disable, 1=enable
gEnableTxBFin20MHz=1
#Enable/Disable SU Tx beamformer support.
gEnableTxSUBeamformer=1
gEnableFastRoamInConcurrency=1
#Maxium Channel time in msec
gMaxMediumTime = 6000
# 802.11K support
gRrmEnable=1
#Enable Power Save offload
gEnablePowerSaveOffload=2
#Enable firmware uart print
gEnablefwprint=0
# Firmware log mode
# Valid values are 0,1,2
# 0=Disable, 1=WMI, 2=DIAG
gEnablefwlog=1
# Maximum Receive AMPDU size (VHT only. Valid values:
# 0->8k 1->16k 2->32k 3->64k 4->128k)
gVhtAmpduLenExponent=7
# Maximum MPDU length (VHT only. Valid values:
# 0->3895 octets, 1->7991 octets, 2->11454 octets)
gVhtMpduLen=2
# Maximum number of wow filters required
#gMaxWoWFilters=22
# WOW Enable/Disable.
# 0 - Disable both magic pattern match and pattern byte match.
# 1 - Enable magic pattern match on all interfaces.
# 2 - Enable pattern byte match on all interfaces.
# 3 - Enable both magic pattern and pattern byte match on all interfaces.
# Default value of gEnableWoW is 3.
# gEnableWoW=0
# Enable or Disable MCC Adaptive Scheduler at the FW
# 1=Enable (default), 0=Disable
gEnableMCCAdaptiveScheduler=1
#Enable or Disable p2p device address administered
isP2pDeviceAddrAdministrated=0
# Remove Overlap channel restriction
gEnableOverLapCh=0
#Enable VHT on 2.4Ghz
gEnableVhtFor24GHzBand=1
#Maximum number of offload peers supported
# gMaxOffloadPeers=2
# controlling the following offload patterns
# through ini parameter. Default value is 1
# to disable set it to zero. ssdp = 0
# Setup multicast pattern for mDNS 224.0.0.251,
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
ssdp=0
#Enable Memory Deep Sleep
gEnableMemDeepSleep=1
# Regulatory Setting; 0=STRICT; 1=CUSTOM
gRegulatoryChangeCountry=1
# RA filtering rate limit param, the current value would not
# help if the lifetime in RA is less than 3*60=3min. Then
# we need to change it, though it is uncommon.
# gRAFilterEnable=0
gRArateLimitInterval=600
# Maximum number of concurrent connections
gMaxConcurrentActiveSessions=3
# Disable/Enable GreenAP
# 0 to disable, 1 to enable, default: 1
gEnableGreenAp=0
# Radar PRI multiplier
gDFSradarMappingPriMultiplier=4
gPNOScanSupport=1
#Enable/Disable LPASS support
# 0 to disable, 1 to enable
gEnableLpassSupport=1
# Whether userspace country code setting shld have priority
gCountryCodePriority=1
# Enable(1)/Disable(0) SIFS burst
gEnableSifsBurst=1
# Enable or Disable Multi-user MIMO
# 1=Enable (default), 0=Disable
gEnableMuBformee=1
# Enable/Disable channel avoidance for SAP in SCC scenario
# 0 - disable
# 1 - enable
gSapSccChanAvoidance=0
# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode
gIbssTxSpEndInactivityTime=10
# Enable TDLS External Control. That is, user space application has to
# first configure a peer MAC in wlan driver towards which TDLS is desired.
# Device will establish TDLS only towards those configured peers whenever
# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
# when teardown criteria (idle packet count and RSSI) is met. However,
# device will accept TDLS connection if it is initiated from any other peer,
# even if that peer is not configured.
# 0 - disable
# 1 - enable
# For TDLS External Control, Implicit Trigger must also be enabled.
gTDLSExternalControl=1
# Enable support for TDLS off-channel operation
# 0 - disable
# 1 - enable
# TDLS off-channel operation will be invoked when there is only one
# TDLS connection.
gEnableTDLSOffChannel=1
# Enable or Disable Random MAC (Spoofing)
# 1=Enable (default), 0=Disable
gEnableMacAddrSpoof=1
################ Datapath feature set Begin ################
# Bus bandwidth threshold values in terms of number of packets
gBusBandwidthHighThreshold=2000
gBusBandwidthMediumThreshold=500
gBusBandwidthLowThreshold=150
# Bus bandwidth compute timeout value in ms
gBusBandwidthComputeInterval=100
# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS=2
gVhtTxMCS=2
# VHT Tx/Rx MCS values for 2x2
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gEnable2x2=1
gVhtRxMCS2x2=2
gVhtTxMCS2x2=2
#IPA config is a bit mask and following are the configurations.
#bit0 IPA Enable
#bit1 IPA PRE Filter enable
#bit2 IPv6 enable
#bit3 IPA Resource Manager (RM) enable
#bit4 IPA Clock scaling enable
#bit5 IPA uC ENABLE
#bit6 IPA uC STA ENABLE
#bit8 IPA Real Time Debugging
gIPAConfig=0x7d
gIPADescSize=800
# Enable/Disable RX full reorder offload
gReorderOffloadSupported=1
# Enable CE classification
# 1 - enable(default) 0 - disable
gCEClassifyEnable=1
# Enable Rx handling options
# Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium)
rx_mode=5
# Enable(Tx) fastpath for data traffic.
# 1 - enable(default) 0 - disable
gEnableFastPath=1
# This flag enables IP, TCP and UDP checksum offload
# 1 - enable(default) 0 - disable
gEnableIpTcpUdpChecksumOffload=1
# Enable TCP Segmentation Offload
# 1 - enable 0 - disable
TSOEnable=1
# Enable Generic Receive Offload
# 1 - enable(default) 0 - disable
GROEnable=1
# Enable HT MPDU Density
# 4 for 2 micro sec
ght_mpdu_density=4
# Enable flow steering to enable multiple CEs for Rx flows.
# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
# Parallel Rx paths.
# 1 - enable 0 - disable(default)
gEnableFlowSteering=1
# Time in microseconds after which a NAPI poll must yield
ce_service_max_yield_time=500
#Maximum number of HTT messages to be processed per NAPI poll
ce_service_max_rx_ind_flush=1
# Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
maxMSDUsPerRxInd=8
# Enable NUD tracking feature
# 1 - enable 0 - disable(default)
gEnableNUDTracking=1
# Enable PEER UNMAP CONF SUPPORT
# 1 - enable 0 - disable(default)
gEnablePeerUnmapConfSupport=1
################ Datapath feature set End ################
################ NAN feature set start ###################
# Enable NAN discovery (NAN 1.0)
# 1 - enable 0 - disable(default)
gEnableNanSupport=1
# Enable NAN Datapath
genable_nan_datapath=1
################ NAN feature set end #####################
adaptive_dwell_mode_enabled=1
hostscan_adaptive_dwell_mode=1
adapt_dwell_lpf_weight=80
adapt_dwell_wifi_act_threshold=10
MAWCEnabled=0
# Enable/Disable rtt sta mac randomization
enable_rtt_mac_randomization=1
#Enable/Disable SNR monitoring
gEnableSNRMonitoring=1
END
# Note: Configuration parser would not read anything past the END marker